Mattsson mkiv RHD-LHD and NA-T Convension

used the car at ouer wedding

you ran 600hp through the w58 box? crazy! ha

my bad didnt read, a w59, whats that? :S

w59 is almost the same as w58 its a Hiace / Hilux 2wd transmission im using the w58 housings on

but i hawe reinforced the housing around the bottom shaft

only reason for using w59 is that they are verry chep and common in the scrapyards

w59 is almost the same as w58 its a Hiace / Hilux 2wd transmission im using the w58 housings on

but i hawe reinforced the housing around the bottom shaft

only reason for using w59 is that they are verry chep and common in the scrapyards

It would be interesting to see a few pics of the modifications?

ahhh ok...

Was the w59 suposed to take 600hp though?

w59 is almost the same as w58 its a Hiace / Hilux 2wd transmission im using the w58 housings on

but i hawe reinforced the housing around the bottom shaft

only reason for using w59 is that they are verry chep and common in the scrapyards

they do a simillar reinforcement on the w58 down here, and w58 can take up to 500 bhp, even they run it on drift cars without issue

now the bmw gs6-53dz arrived from germany

when the W59 is of the car i will post pic of the housing.

The gears are still fin only hawe problem with shiifter fork that come lose

Fantastic build mate

used the car at ouer wedding

[ATTACH=CONFIG]156904[/ATTACH]

[ATTACH=CONFIG]156905[/ATTACH]

Congratulations...! That's a sick burnout in the parking lot..! ILMAO.....!

Her is a pic of the welding on the outside of the housing i hawe no pic of the inside

but i hawe filled the empty room under the lower shaft front bering just above the outside modification

hope this explains what i meean.

And then i hawe a new fault with the W59 box the 3-4 Syncro slider

But now to the mor fun part the Mod off the Bmw ZF Gerbox

First Cut apart aprox 95mm must go

Then you nead aprox 55mm of the Auto Bellhousing - 1-3mm of adjustment

shold not be flush when welding i prefere 1mm gap.

Her you can also see the Hub that is screewd down to the Crank shaft

New pilot bering is neeaded to 6002 fits right on

then its just to start welding it all toghether 4-5cm at the time

and when the outside is done its tim for the inside.

all done

also i got a set of used 17inch oem wheels 8" front 9,5" rear

Those will work better with my Euro Brakes.

Nice work mate you certainly dont hang about good enthusiasm

Thank you for posting the W59 upgrade pic.

Nice job on the bell-housing, I hope it proves to align well.

When it does, you're going to be a busy man knocking those out.

You're lucky you're so far away, or I'd be visiting with pieces of aluminium castings for you to weld together.

Very nice work mate !!!

congrats!!!!!!!!!

Thanks

Today i hawe removed all the interior

hawe orderd a new carpet from stockinteriors.com that just cleard customs so im going to put that in more picures as work continue

Fantastic mate! Love your work.

Some Spedparts AN8 Fragola and a fuel filter

Also baut a Oil cooler that i will feed froma Whaler Thermo block from a Volvo B230ET Red block

in my opinion Termostat on the oil is verry important so you reach oil temp fast and then hawe a stabel temp.

Pressure plate from Sachs 999 765

Flywheel from Comp Clutch

Still wating for my 6puck Sprung hub from Clutchnet

The Carpet from Stockinteriors is nothing i can recomend. Buy a OEM insted !

its made out off good material but they mould it directly on the floor without evening out the floor befor with some fome.

Parts from Elmhust thanks to Curt

EGood work! I asume you bought a Lhd indicator and wiper selector switch, was it very expensive?

reading through this and the amount of work you have done, fair play. great pic's to show your work too

EGood work! I asume you bought a Lhd indicator and wiper selector switch, was it very expensive?

it was 262$ in US at Elmhurst in Sweden They are twice that price or more

im trying to sorece a LHD Wiper Crowl Cover the price in Sweden is over 500£ and 150£ in Us but shipping is expensive from Us so it makes no diffrence...

Somone sitting on one and wold like to shipp it to sweden pls let me know

I hawe a freindes addres in Dodrecht NL that is possible to send to if its cheaper than direct to Sweden

Thanks evryone fore the positve response

you ot some really nice stuff going in ther ;D

hi mate iv got one of thes bmw gearboxes for cheap money is yours runing allready how does it feel?

this is what i hawe done today in my lathe

34rpm

it was 0.8mm off

it moves slow right now

Fabulous work, I can see lasers in your eyes.

I think you should knock-up a 100 whilst your jigged up for the job.

Thanks

now i will not make annything on the car since i hawe had surgery to my leg for the third time in since 2009

... so the season will be short just hope to be able to run it in the end of this year