SkyJawa Posted October 1, 2003 Share Posted October 1, 2003 Just got it from Chris, hoping to get it on the car tomorrow as I'm running on the rollers on Sat and at the mo its hitting 1.4 bar, so not a good combination!!!! My thoughts are to put it in the joint between the first and second decat pipe? Any thoughts? Link to comment Share on other sites More sharing options...
Chris Wilson Posted October 1, 2003 Share Posted October 1, 2003 Originally posted by HISUPE Just got it from Chris, hoping to get it on the car tomorrow as I'm running on the rollers on Sat and at the mo its hitting 1.4 bar, so not a good combination!!!! My thoughts are to put it in the joint between the first and second decat pipe? Any thoughts? Either there or between 2nd cat pipe and rest of system are both fine. Link to comment Share on other sites More sharing options...
SkyJawa Posted October 1, 2003 Author Share Posted October 1, 2003 Straight from the horses mouth - superb! Thanks Chris, and cheers for getting it here so quick since you're rather busy Link to comment Share on other sites More sharing options...
MONKEYmark Posted October 1, 2003 Share Posted October 1, 2003 just got mine through post, dont seem to be overboosting since i had torque convertor fitted? feels fast but only hitting 1.1bar will have to keep it in car if i start to overboost. let us know wht your boost goes down to when you fit it Link to comment Share on other sites More sharing options...
SkyJawa Posted October 1, 2003 Author Share Posted October 1, 2003 No probs mate - will do, should hopefully pop into a tyre/exhaust place at lunch (thurs) to get it whacked in...... Link to comment Share on other sites More sharing options...
Matt Harwood Posted October 2, 2003 Share Posted October 2, 2003 I stuck mine it at the rear pipe/exhaust. Purely as I though it would keep the heat build up away from the engine... Worked a treat (another one of Chris's happy customers!) Link to comment Share on other sites More sharing options...
SkyJawa Posted October 2, 2003 Author Share Posted October 2, 2003 Tried again this morning, bit warmer than last week and still hitting 1.3, so this should work a treat. Got it with me to pop to a local exhaust place at lunch where I'll ask for it to be put between the 2nd cat pipe and the rear section Had a thought though - will I need an extra gasket or anything? Got a Toyota dealer 2 secs down the road if so!! Link to comment Share on other sites More sharing options...
SkyJawa Posted October 2, 2003 Author Share Posted October 2, 2003 Got it fitted. Done a few initial "tests" but the car was not as warmed up as on my journey in and its warmed up temp wise so true test will be am. However - its gone from 1.3 this morning, to no more than 0.95 on the gauge now!!!! Mmmmmmmm time for a boost controller LOL! Link to comment Share on other sites More sharing options...
Ian C Posted October 2, 2003 Share Posted October 2, 2003 Just file it out a bit -Ian Link to comment Share on other sites More sharing options...
SkyJawa Posted October 2, 2003 Author Share Posted October 2, 2003 I guess that would make more sense, but then I shouldn't I wait for the colder weather first? Link to comment Share on other sites More sharing options...
dandan Posted October 2, 2003 Share Posted October 2, 2003 Hey guys, Just got a couple of questions regarding decat pipes. My lower cat is gone (thanks to HKS pipe I think) and i'm considering getting rid of top cat now too. I wondered what size (internal diameter) these top decat pipes were - and whether they match up internally to turbo outlet or if there's a step change in diameter? I'm running a J spec (I know there are slight differences in pipes for uk) Thanks Link to comment Share on other sites More sharing options...
SkyJawa Posted October 2, 2003 Author Share Posted October 2, 2003 Not sure I can help you mate, I'm sure some-one else will! On another note - Chris, if the boost stays a bit too low, how much can I open the hole up to raise it - eg, have you any method to say from what I have now, what to open the hole by to gain another 0.1 bar etc.....? Otherwise I guess its plenty of trial and error or a boost controller! Link to comment Share on other sites More sharing options...
Chris Wilson Posted October 2, 2003 Share Posted October 2, 2003 Make the hole 2mm bigger in diameter, no more. Try that and let me know. It's impossible to make them EXACTLY right, but I usually get close, so don't go making it 5mm bigger ! Link to comment Share on other sites More sharing options...
SkyJawa Posted October 2, 2003 Author Share Posted October 2, 2003 Top stuff, thanks Chris As I said, I'm not going to do it straight away, as you might have got it spot on for when the colder stuff gets here I certainly appreciate its not an exact science, and indeed the way I see it, hitting 0.95 bar is far better than hitting 1.35 on standard J-Spec fueling so at least I can progress from a safe point See how it goes and may then enlarge it the 2mm if its still a tad low, I'll be after a boost controller next year anyway I imagine so its not a big deal! Thanks for all the help Chris - much appreciated! Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now