Tricky-Ricky Posted January 12, 2007 Share Posted January 12, 2007 Just wondering if anyone has got any of the external voltage inputs connected and set up, same goes for the temp sensor? is there anything special about the input harness, and does the temp sensor input require a Blitz sender to work? this also applies to the SBC I-color. Link to comment Share on other sites More sharing options...
Tricky-Ricky Posted January 13, 2007 Author Share Posted January 13, 2007 Has nobody got any of these hooked up? Link to comment Share on other sites More sharing options...
Homer Posted January 13, 2007 Share Posted January 13, 2007 Can't offer any direct advice but beleive Lui may have these set up. Link to comment Share on other sites More sharing options...
Tricky-Ricky Posted January 13, 2007 Author Share Posted January 13, 2007 I'll keep bumping this in the hope someone can answer:) Link to comment Share on other sites More sharing options...
Tricky-Ricky Posted January 14, 2007 Author Share Posted January 14, 2007 Up again! Link to comment Share on other sites More sharing options...
Alonso Posted April 29, 2007 Share Posted April 29, 2007 Hi there I'm doing the same stuff actualy. I want to use the id-3 for some temperature measurement. First, some facts; -There is no need tu buy the f*** expensive harness from blitz. You'll only need a fitting connector. Have a look to your favourite electronic discounter. -The Pinout of the SBC id-3 http://supra.alonso.ch/d/222-1/67.jpg You only need a fixed reference voltage (f.e. 5vdc) for the sensory supply. You can get them with a LM7805 component or similar. Then, you can use any fitting temperature sensor, NTC or PTC does'nt matter. Add a secundary resistor to limit the current. Connect the middle between the temperature sensor and the resistor to the input of the sbc, and set the parameters in the settings menu. F.e. 1VDC --> 10°C, 4VDC --> 90°C. Of course you have to calculate these values, but this should be an easy lesson for anyone with some electonic knowlegde. I can post you my complete solution in a few weeks. There is some more important work to do first You hope you can understand my english Kind regards Link to comment Share on other sites More sharing options...
MarkR Posted July 20, 2007 Share Posted July 20, 2007 Sounds good. Any further development? Link to comment Share on other sites More sharing options...
joeblitz Posted July 20, 2007 Share Posted July 20, 2007 blitz sell a harness as far as i remember its only 30 stg connecting to 3 data connections with an output 0-16v etc water temp ,throttle , airflow ... try fensport for connector ..i fitted one before easy as pie Link to comment Share on other sites More sharing options...
MarkR Posted July 21, 2007 Share Posted July 21, 2007 blitz sell a harness as far as i remember its only 30 stg connecting to 3 data connections with an output 0-16v etc water temp ,throttle , airflow ... try fensport for connector ..i fitted one before easy as pie Cheers matey Link to comment Share on other sites More sharing options...
MarkR Posted August 15, 2007 Share Posted August 15, 2007 okay, here's a silly question. Where do the wires go? I have the harness but no idea what the wires mean (jap instructions)... Link to comment Share on other sites More sharing options...
Guest nismo502 Posted October 20, 2014 Share Posted October 20, 2014 Sorry to bump up a very old thread. But have anyone got this working? How do you wire it up? What is your data settings for water temp sensors? I tried to hook in a defi water sensor, 1 goes to ground the other goes to data2, not working. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now