Jim_1979 Posted December 21, 2006 Share Posted December 21, 2006 Ok... got a HKS FCD from uksupra.. cheers! (now I know the HKS isn't regarded as good as the thor/greddy etc!) The FCD has a dial on the front which goes from 1 to 12 and 4 wires. I've done a bit of searching for the past few minutes on the forums looking for info. So far I've sussed out that the dial needs to be set to 9. (is this right??) The FCD has a red, black, yellow and white wire. I assume the red and black are positive and earth. What about the white and yellow? Where do these connect to?? Also where do the red and black connect to ? To a switched live and earth or points on the ECU wires?? Any help much appreciated! If this info has already been posted, then sorry!! ... but I did search! Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted December 21, 2006 Author Share Posted December 21, 2006 bump! (sorry, but want to sort this tomorrow... ) Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted December 22, 2006 Author Share Posted December 22, 2006 anyone? Quote Link to comment Share on other sites More sharing options...
Ric Posted December 22, 2006 Share Posted December 22, 2006 the white and yellow should be the map sensor wire, but for which wire goes to which side (ecu or loom side) i couldnt advise. try to find a wiring diagram off ebay or from one of the traders who sell that unit. Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted December 22, 2006 Author Share Posted December 22, 2006 Will give Nic a shout... see if he can be of any help. ta Quote Link to comment Share on other sites More sharing options...
jamesmark Posted December 22, 2006 Share Posted December 22, 2006 Does this help? link Quote Link to comment Share on other sites More sharing options...
Ibrar Jabbar Posted December 22, 2006 Share Posted December 22, 2006 Here you go http://www.hksusa.com/info/download.asp?id=1793 Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted December 22, 2006 Author Share Posted December 22, 2006 ok... so 9 is the correct setting?? Also how to you get access to the ECU? It says go in from the passenger side, but is that on an American car?? Can't you just get access from removing the stereo etc? Quote Link to comment Share on other sites More sharing options...
jamesmark Posted December 22, 2006 Share Posted December 22, 2006 Think of it as looking in a mirror. It's reversed just follw the guide. Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted December 22, 2006 Author Share Posted December 22, 2006 lol.... ok. Quote Link to comment Share on other sites More sharing options...
Nic Posted December 23, 2006 Share Posted December 23, 2006 ok... so 9 is the correct setting?? Also how to you get access to the ECU? It says go in from the passenger side, but is that on an American car?? Can't you just get access from removing the stereo etc? The ECU is in the passenger footwell, lift up the carpet and you'll find a black plastic cover, remove botls and you'll find the ECU under there, it is the RHS metal box. See FCD instructions attached.FCD manual.pdfECU Pin Out.pdf Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted December 23, 2006 Author Share Posted December 23, 2006 cheers Nic Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.