ManwithSupra Posted September 14, 2006 Share Posted September 14, 2006 Does anyone know what i would need to replace if i want to refurb the exisitng sequential setup I am looking at staying with hybrids and as i will be going with them i want to refurn the old system. Before anyone says i dont want to go single cos i like the original setup Link to comment Share on other sites More sharing options...
Bob Posted September 14, 2006 Share Posted September 14, 2006 Depends on budget mate. A total refurb with new parts would be into the thouands. Link to comment Share on other sites More sharing options...
ManwithSupra Posted September 14, 2006 Author Share Posted September 14, 2006 Well i have been having an issue with number 2 at the moment, Seems to not come online then all of a sudden it does i have been told that this is a sequential system problem somthing to do with a valve, mainly i want to get this sorted really. Link to comment Share on other sites More sharing options...
Bob Posted September 14, 2006 Share Posted September 14, 2006 WD40 the EGBV actuator arm (down the back of number 2) and replace the vacuum hoses. Most people go for silicon hoses for looks, but ideally go for rubber hoses (you can get cotton-braided rubber vacuum hose from Demon Tweeks) would be a good start. Also replace the EGCV hoses and check the VSVs and actuator valves. The EGBV pipes are an absolute b*stard. Expect a lot of swearing and scraped knuckles! :edit: I had problems with no2 previously where it was stuttering, turned out to be duff coil-packs (I think - I replaced the fuel pump at the same time as well though) If everything else is fine, it could also be your pressure tank has popped it's clogs which would explain no pre-spool (well, that's my understanding of it anyway! ) Link to comment Share on other sites More sharing options...
Dragonball Posted September 14, 2006 Share Posted September 14, 2006 My bad - thought he meant turbos... DOH! Link to comment Share on other sites More sharing options...
Ian C Posted September 14, 2006 Share Posted September 14, 2006 Mmm I think he meant the sequential system and not the actual turbo units It's a tricky thing to refurb, you'd have to take the turbos off, which immediately gives you a couple of hundred quid in gaskets and coolant and oil and stuff, as well as a nightmare taking the damn things off. Then check and replace if necessary each hose (lots of them). Check the function of each VSV and make sure they can be energised from the wiring in the footwell. Make sure the actuators work and aren't sticky. And test the pressure tank too, which is another nightmare to get to. Then bolt it all back together. It's kinda easier just to fix each problem as they come along -Ian Link to comment Share on other sites More sharing options...
ManwithSupra Posted September 14, 2006 Author Share Posted September 14, 2006 WD40 the EGBV actuator arm (down the back of number 2) and replace the vacuum hoses. Most people go for silicon hoses for looks, but ideally go for rubber hoses (you can get cotton-braided rubber vacuum hose from Demon Tweeks) would be a good start. Also replace the EGCV hoses and check the VSVs and actuator valves. The EGBV pipes are an absolute b*stard. Expect a lot of swearing and scraped knuckles! :edit: I had problems with no2 previously where it was stuttering, turned out to be duff coil-packs (I think - I replaced the fuel pump at the same time as well though) If everything else is fine, it could also be your pressure tank has popped it's clogs which would explain no pre-spool (well, that's my understanding of it anyway! ) Which one is my pressure tank - your not talking about fuel tank are you ? Link to comment Share on other sites More sharing options...
Bob Posted September 14, 2006 Share Posted September 14, 2006 The pressure tank is a little cylindrical, um, tank hidden under your inlet manifold iirc and pressurizes the actuators to help them work freely or something like that. AFAIK it's a ball-ache to get out but easy enough to test. I'll see if I can scan in the Toyota manual pages this evening Link to comment Share on other sites More sharing options...
ManwithSupra Posted September 14, 2006 Author Share Posted September 14, 2006 That would be great if you could Link to comment Share on other sites More sharing options...
ManwithSupra Posted September 14, 2006 Author Share Posted September 14, 2006 Did you have any luck with getting the stuff from the manual? Link to comment Share on other sites More sharing options...
Bob Posted September 14, 2006 Share Posted September 14, 2006 Sorry mate, been golfing [badly]. Scanner's dead, so I've had to photograph them. Here ya go: Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now