jcbt Posted February 23, 2015 Share Posted February 23, 2015 Turbo Kit Fwends....! Sure are - can't wait to see the difference - Dragonball will be a whole lot of fun for us Precision boys this year;) Link to comment Share on other sites More sharing options...
Fitz Posted February 23, 2015 Share Posted February 23, 2015 Sure are - can't wait to see the difference - Dragonball will be a whole lot of fun for us Precision boys this year;) I'll keep an eye on the rear of your cars for you both.... Link to comment Share on other sites More sharing options...
Wez Posted February 23, 2015 Share Posted February 23, 2015 Slightly off topic I know, but why do people place the BOV there? Isn't it better served much closer to the throttle body? Cheap packaging, most kits came with pipework only up to either a SMIC or FMIC. My kit many years ago had the same setup but it was binned as I already had the HKS throttle body elbow with the SQSS fitting as in the pic Link to comment Share on other sites More sharing options...
TheTurtleshead Posted February 23, 2015 Share Posted February 23, 2015 Sure are - can't wait to see the difference - Dragonball will be a whole lot of fun for us Precision boys this year;) Well if you're aiming to push that turbo all the way to 900hp you'll spank me on the straights with my little 62mm! Link to comment Share on other sites More sharing options...
jcbt Posted February 23, 2015 Share Posted February 23, 2015 Well if you're aiming to push that turbo all the way to 900hp you'll spank me on the straights with my little 62mm! James we are only aiming for around 650hp at this stage;) Link to comment Share on other sites More sharing options...
TheTurtleshead Posted February 23, 2015 Share Posted February 23, 2015 James we are only aiming for around 650hp at this stage;) I'm aiming to make 600+. Should do it with my fuelling, cams and turbo. So long as it hits 600 I don't mind, anything more is a bonus! Link to comment Share on other sites More sharing options...
jcbt Posted February 23, 2015 Share Posted February 23, 2015 I'm aiming to make 600+. Should do it with my fuelling, cams and turbo. So long as it hits 600 I don't mind, anything more is a bonus! Fast spooling 600 + hp is still going to be mind blowing Link to comment Share on other sites More sharing options...
Guest Budz86 Posted February 23, 2015 Share Posted February 23, 2015 What fuel system you running John? Link to comment Share on other sites More sharing options...
TheTurtleshead Posted February 23, 2015 Share Posted February 23, 2015 Fast spooling 600 + hp is still going to be mind blowing I hope so I really think 6-700 is the sweet spot for a Supra. Can't wait to hang the arse out round many, many roundabouts on DB. Link to comment Share on other sites More sharing options...
jcbt Posted February 23, 2015 Share Posted February 23, 2015 What fuel system you running John? Currently ID 1000's with a Walbro 455 pump Link to comment Share on other sites More sharing options...
Style Posted February 23, 2015 Share Posted February 23, 2015 Another great build getting put together, will be watching with interest! These Gen 2 Precision turbos are a massive game changer for the Supra clan it seems Link to comment Share on other sites More sharing options...
Guest Budz86 Posted February 23, 2015 Share Posted February 23, 2015 Currently ID 1000's with a Walbro 455 pump Cool. Guessing you're not gonna bother with a twin pump setup or fuel flex then as you're a bit restricted by the box? Link to comment Share on other sites More sharing options...
Chris Bailey Posted February 23, 2015 Share Posted February 23, 2015 Cool. Guessing you're not gonna bother with a twin pump setup or fuel flex then as you're a bit restricted by the box? The walbro 450lph pump is good for 800bhp on a single pump, was going to go with fuel flex and run ethanol but decided against it. Will probably have that done when we change the inlet manifold. Not sure our ID1000's are capable for ethanol. Thats another reason why we didnt. The gearbox should take 700bhp, maybe more with 2x trans coolers. Link to comment Share on other sites More sharing options...
jcbt Posted February 23, 2015 Share Posted February 23, 2015 Cool. Guessing you're not gonna bother with a twin pump setup or fuel flex then as you're a bit restricted by the box? Dean the box is not the limiting factor as it's a Boostlogic built box. The engine currently has ARP rods and bolts and Clevite bearings so not fully built so would not want to push it higher at present. Will be reviewing intake and fuelling when we do the next stage hopefully later in the year Link to comment Share on other sites More sharing options...
Kaan W Posted February 23, 2015 Share Posted February 23, 2015 The walbro 450lph pump is good for 800bhp on a single pump, was going to go with fuel flex and run ethanol but decided against it. Will probably have that done when we change the inlet manifold. Not sure our ID1000's are capable for ethanol. Thats another reason why we didnt. The gearbox should take 700bhp, maybe more with 2x trans coolers. Boostlogic claim to have run 8s on that box mate, with coolers you shouldn't have anything to worry about. Link to comment Share on other sites More sharing options...
Chris Bailey Posted February 23, 2015 Share Posted February 23, 2015 Boostlogic claim to have run 8s on that box mate, with coolers you shouldn't have anything to worry about. But then saying that, Jamesy blew one up at 825bhp! Link to comment Share on other sites More sharing options...
Kaan W Posted February 23, 2015 Share Posted February 23, 2015 But then saying that, Jamesy blew one up at 825bhp! I know the newest ones have the billet sprag don't they? Not sure what blew on James's though I think it's just pure luck sometimes as well as a good map. Mapping tech has moved forward since then. Link to comment Share on other sites More sharing options...
Chris Bailey Posted February 23, 2015 Share Posted February 23, 2015 I know the newest ones have the billet sprag don't they? Not sure what blew on James's though I think it's just pure luck sometimes as well as a good map. Mapping tech has moved forward since then. Yeah im aware they updated them, think ours might be the uprated one. Its been okay for well over a year now *touch wood* Link to comment Share on other sites More sharing options...
Lee P Posted February 23, 2015 Author Share Posted February 23, 2015 The walbro 450lph pump is good for 800bhp on a single pump, was going to go with fuel flex and run ethanol but decided against it. Will probably have that done when we change the inlet manifold. Not sure our ID1000's are capable for ethanol. Thats another reason why we didnt. The gearbox should take 700bhp, maybe more with 2x trans coolers. The single pump system will only do high 600s Link to comment Share on other sites More sharing options...
Chris Bailey Posted February 23, 2015 Share Posted February 23, 2015 The single pump system will only do high 600s Im Whifbitz advertise it capable of 800bhp, that might be on ethanol though. Link to comment Share on other sites More sharing options...
Lee P Posted February 23, 2015 Author Share Posted February 23, 2015 Im Whifbitz advertise it capable of 800bhp, that might be on ethanol though. Not on the stock fuel line, its worse on Ethanol don't forget as you need 30% more fuel Jamie's fuel system was maxed before we change to twin pump system Link to comment Share on other sites More sharing options...
Chris Bailey Posted February 23, 2015 Share Posted February 23, 2015 Not on the stock fuel line, its worse on Ethanol don't forget as you need 30% more fuel Jamie's fuel system was maxed before we change to twin pump system Ahhh yes ofcourse Dont listen to me lol. Link to comment Share on other sites More sharing options...
jcbt Posted February 23, 2015 Share Posted February 23, 2015 The single pump system will only do high 600s Thanks Lee for the clarification Link to comment Share on other sites More sharing options...
mattdavies Posted February 23, 2015 Share Posted February 23, 2015 Ahhh yes ofcourse Dont listen to me lol. Don't think many people do Looks good Mr Bailey, look forward to the outcome Link to comment Share on other sites More sharing options...
Luxluc Posted February 23, 2015 Share Posted February 23, 2015 I would go for a staggered twin pump setup. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now