Josh42 Posted May 23, 2013 Share Posted May 23, 2013 Why don't you do a drop test mate? At least you'll know which cylinder is missing? Disconnect the clips from each of the leads where they connect to the distributor cap. Start the car and using an INSULATED pair of pliers and INSULATED gloves and being very careful, drop one lead out of the distributor at a time and replace it after a few seconds. When you notice that the engine pitch doesn't change, that's your dead cylinder. It'll be either a dead plug or lead if not water in the well. Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) ................. Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) ............. Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 uhm was thinking of trying that tomozz..just run outa light tonight...and patience ha......im wondering if if number 5 and number 6 were drowning in water, wether they have broken..and need replacement now......hope i dont need new HT leads......ok thank you josh...will try tomorrow Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) its gotta be down line of the distributer....plugs or leads...yes ...i can see what you all thinking... Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Josh42 Posted May 23, 2013 Share Posted May 23, 2013 (edited) You can't have done really mate. The ignition system on the GE engine is very basic, so therefore can only be something basic... Edited May 23, 2013 by Josh42 (see edit history) Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) hope its a plug....60 gbp though for a set :/...if she needs it she needs it...I just changed them not to long ago...I am never cleaning my engine again hahaha Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Josh42 Posted May 23, 2013 Share Posted May 23, 2013 You'll pick plugs up for a lot less than £60 mate:) Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 Oh i see,, mmm...thats what ive been quoted so far form two diffrent motor parts supplyers..... - - - Updated - - - it cost me that last time i bought some for her. Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) maybe i should look around abit more for other prices? for some..mmm might be a good idea...thank you josh. Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) .................. Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Rich.2211 Posted May 23, 2013 Share Posted May 23, 2013 If you haven't already (only skim read the thread) then take the distributor cap off and check it is completely dry inside. If the engine bay is damp then condensation can form in the cap and voila one engine running rougher than a bears backside. Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 23, 2013 Share Posted May 23, 2013 (edited) i havnt seen many bears back ends..but im sure there rough aha....thanks rich....mmm checked the distributer cap, and it seemed dry in there, no condensation......thank you though...all helps...everything seems dry this is what i cant make out?......maybe running with the two rear plugs doing a jack couste swimming has damaged them?........i shall take mr joshes advice and try to find the dead cylinders tomorrow, i`ll double make sure, i`ll spray all electrical connectors with MR WD40 fish oil.......and then hair dry every connector and HT lead ....we will find this gremiln fellas!!!! Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Guest last light bulb Posted May 24, 2013 Share Posted May 24, 2013 (edited) :rolleyes:Still awaiting parts... oh well never mind...will get there eventualy i suppose ;/ Edited May 24, 2013 by last light bulb (see edit history) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.