Hellstrom Posted April 5, 2012 Share Posted April 5, 2012 (edited) Hi! my car is finally up and running again however the yellow traction control light keeps flashing and its driving me nuts.... i had the intention of polishing my throttle body so i removed all the sensors (TPS,Subtps,TC acutator/motor) now i cant seem to get it back to stop flashing. i used the TSRM trying to reset the sub TPS etc but i guess with no luck as the light is still flashing, i aslo tried to messure ohm from the motor itself acording to the TSRM but i could not get a readout dunno it says 0,85ohm but my tool only messure to 200ohm as lowest (i should get a 0.x readout imo but i dont) So any ideas that flashing yellow light is killing me... 1. INSPECT SUB–THROTTLE ACTUATOR Using an ohmmeter, measure the resistance between the terminals (ACM to A and A–, BCM to B and B–). Resistance: 0.82–0.98 at 20°C (68°F) If the resistance is not as specified, replace the actuator. Edited April 5, 2012 by Hellstrom (see edit history) Link to comment Share on other sites More sharing options...
CanisLupus Posted April 5, 2012 Share Posted April 5, 2012 If it's a JSPEC Throttle Body set it up with this one attached Jspec 2JZGTE TPS adjustment.pdf Link to comment Share on other sites More sharing options...
mplavery Posted April 5, 2012 Share Posted April 5, 2012 Mine doing the same thing since I took the throttle body off to get it polished, at first it was annoying and I was going to sort it , now I like it this way as the slip control is always off which I prefer.... I always used to forget to turn it off when I wanted to have a play Link to comment Share on other sites More sharing options...
dr_jekyll Posted April 5, 2012 Share Posted April 5, 2012 just pull the fuse and be done with it. grrrrrrrr man car Link to comment Share on other sites More sharing options...
Hellstrom Posted April 5, 2012 Author Share Posted April 5, 2012 If it's a JSPEC Throttle Body set it up with this one attached [ATTACH=CONFIG]149442[/ATTACH] Ill try it tomorrow not verry easy to understand everything there tho But ill give it my best Link to comment Share on other sites More sharing options...
Hellstrom Posted April 6, 2012 Author Share Posted April 6, 2012 Sorted it. Thanks Link to comment Share on other sites More sharing options...
mplavery Posted April 6, 2012 Share Posted April 6, 2012 How did you sort it in the end ? Link to comment Share on other sites More sharing options...
Hellstrom Posted April 6, 2012 Author Share Posted April 6, 2012 Removed the throttle boddy and made a factory reset according to the jap tsrm Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted October 1, 2012 Share Posted October 1, 2012 Removed the throttle boddy and made a factory reset according to the jap tsrm Them instructions were not the best .. did you fiddle with this for a bit or first time lucky ? Link to comment Share on other sites More sharing options...
p3te Posted May 18, 2013 Share Posted May 18, 2013 bump, how did you set the sensors up? i think mine needs resetting after messing with the tps and sub tps trying to sort a high idle, the traction control light flashes all the time now, ive tried adjusting the sub tps a bit but it still flashes Link to comment Share on other sites More sharing options...
Hellstrom Posted May 18, 2013 Author Share Posted May 18, 2013 I just did a factory reset from the instruction above. I was pretty ease with a ohm meter and the mesuring tool. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now