marc_p Posted April 28, 2011 Share Posted April 28, 2011 Ok, starting to get frustrated now, been working on the car all night and trying to figure out 2 things: 1) Where the hell do you run wires through the bulkhead? I have half the dash out and still can't find anywhere 2) Below is a pic of the t-piece next to the pipe I 'think' I'm suppost to cut in half to place it in, can anyone confirm before I end up slicing the wrong pipe? Any help will be greatly appreciated. Thanks Marc Quote Link to comment Share on other sites More sharing options...
marc_p Posted April 29, 2011 Author Share Posted April 29, 2011 Anyone? Quote Link to comment Share on other sites More sharing options...
fastnfurious Posted April 29, 2011 Share Posted April 29, 2011 check out my pixs dude... http://www.mkivsupra.net/vbb/showthread.php?244988-Project-quot-Samco-Sport-amp-Hallman-quot-replaced-old-vacuum-hoses-amp-MBC Quote Link to comment Share on other sites More sharing options...
fastnfurious Posted April 29, 2011 Share Posted April 29, 2011 (edited) ok, here you go... just tap onto the hose below the turbo pressure sensor port or unless my setup is wrong all these while but i doubt so! Edited April 29, 2011 by fastnfurious (see edit history) Quote Link to comment Share on other sites More sharing options...
TTRickeh Posted April 29, 2011 Share Posted April 29, 2011 I'd stear clear of those pipes. They are for important things like MAP and fuel pressure. I use the one coming off the other side of the manifold going to the power steering, or you could use the one in the very bottom right hand corner of fastnfurious' pic. Quote Link to comment Share on other sites More sharing options...
fastnfurious Posted April 29, 2011 Share Posted April 29, 2011 (edited) @Marc: it seems that your current hose connection is not the exact/correct factory setup! have a look at mine... Edited April 29, 2011 by fastnfurious (see edit history) Quote Link to comment Share on other sites More sharing options...
marc_p Posted April 29, 2011 Author Share Posted April 29, 2011 Cheers for the pointers guys, finally did it, although not too happy with the a-pillar gauge holder, it doesn't fit great Quote Link to comment Share on other sites More sharing options...
TTRickeh Posted April 29, 2011 Share Posted April 29, 2011 @Marc: it seems that your current hose connection is not the exact/correct factory setup! have a look at mine... His is the same as mine and the technical references on this site http://www.mkivsupra.net/vbb/attachment.php?attachmentid=13939&d=1112558977 Quote Link to comment Share on other sites More sharing options...
Robzki Posted April 29, 2011 Share Posted April 29, 2011 Cheers for the pointers guys, finally did it, although not too happy with the a-pillar gauge holder, it doesn't fit great Out of interest I'm on the lookout for a pillar pod, Which one have you got? so I know what to avoid. Quote Link to comment Share on other sites More sharing options...
marc_p Posted April 29, 2011 Author Share Posted April 29, 2011 Out of interest I'm on the lookout for a pillar pod, Which one have you got? so I know what to avoid. The one on ebay that covers the entire a-pillar, it's better than a screw on one but doesn't cover the a-pillar very well. Quote Link to comment Share on other sites More sharing options...
Lude Posted April 30, 2011 Share Posted April 30, 2011 plumb into the pipe on the side of the intake manifold, there is a gromet alson on that side, just behind the intake manifold and down slightly. il get pics now... Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.