Swampy442 Posted April 11, 2010 Share Posted April 11, 2010 TD04 based hybrids for sale, brand new, 360 bearings, cut back turbines, enlarged wastegates etc Needs a UK manifold which will be included (hasnt arrived yet but its included when it does) Bought for my Aristo but selling the car so no longer reqd. Not sure about postage as the whole lot will weigh a ton, collection preferred or I can deliver within a reasonable distance of Lincoln/Henley. £750 Link to comment Share on other sites More sharing options...
Pixelfill Posted April 11, 2010 Share Posted April 11, 2010 What other supporting mods would be required to sensibly fit these Craig? You not tempted to fit these to your replacement car instead Mike Link to comment Share on other sites More sharing options...
TRD-Rob Posted April 11, 2010 Share Posted April 11, 2010 What kind of power would you get from this ? Link to comment Share on other sites More sharing options...
johnny g Posted April 11, 2010 Share Posted April 11, 2010 I'm guessing you'll be needing the BPU list of mods, plus some 550 injectors and an ECU? Link to comment Share on other sites More sharing options...
pistonbroke Posted April 11, 2010 Share Posted April 11, 2010 Where did these come from mate? Link to comment Share on other sites More sharing options...
Pixelfill Posted April 11, 2010 Share Posted April 11, 2010 Yeah Johnny, just not knowing how much air these would flow whether 550s would be large enough, and whether a piggyback ecu would cope. Mike Link to comment Share on other sites More sharing options...
Kirk Posted April 11, 2010 Share Posted April 11, 2010 Tempted mike? Link to comment Share on other sites More sharing options...
Pixelfill Posted April 11, 2010 Share Posted April 11, 2010 possibly Mike Link to comment Share on other sites More sharing options...
Kirk Posted April 11, 2010 Share Posted April 11, 2010 Dont blame you mate, i suspect you could make some serious power over stock twins with supporting mods Link to comment Share on other sites More sharing options...
ray007 Posted April 11, 2010 Share Posted April 11, 2010 selling ur Aristo? how comes? how much u after for the Aristo mate? Link to comment Share on other sites More sharing options...
johnny g Posted April 11, 2010 Share Posted April 11, 2010 I'm guessing they're good for about 300-350bhp each? I know the TD06 on the MR2 was a good 420-450bhp turbo at respectable boost. I'd say you'd be looking at a good 500-550bhp, relatively easily? Link to comment Share on other sites More sharing options...
JamieP Posted April 11, 2010 Share Posted April 11, 2010 Never seen these before, they still work in sequential? and when used on a uk manifold everything else will bolt right up? Link to comment Share on other sites More sharing options...
Kirk Posted April 11, 2010 Share Posted April 11, 2010 That would be nice in sequential mode Link to comment Share on other sites More sharing options...
pistonbroke Posted April 11, 2010 Share Posted April 11, 2010 Never seen these before, Me too, thats why I want to know where they came from. Link to comment Share on other sites More sharing options...
Carl Posted April 11, 2010 Share Posted April 11, 2010 As has been asked already, what mods would be needed to get these running. I have J-spec so assume UK injectors for a starters but what else is needed to get these running safely? Carl Link to comment Share on other sites More sharing options...
Swampy442 Posted April 11, 2010 Author Share Posted April 11, 2010 What other supporting mods would be required to sensibly fit these Craig? You not tempted to fit these to your replacement car instead Mike Mike, Walbro or similar pump, 550 injectors, basically BPU upgrades would run them but obviously if you had an aftermarket ECU you could get better results. Wont need hybrids with a T67 DBB under the bonnet What kind of power would you get from this ? Well, theres the question, all the hybrid haters will tell you not much more than BPU, Id say up towards 500. I was quoted 550 but thems American figures lol. Where did these come from mate? They came from the States Yeah Johnny, just not knowing how much air these would flow whether 550s would be large enough, and whether a piggyback ecu would cope. Mike I havent got CFM figures so cant tell you peak flows but 20psi is easily achievable selling ur Aristo? how comes? how much u after for the Aristo mate? Aristo's sold mate sadly. Ive gone and bought thw Do Luck Aristo Never seen these before, they still work in sequential? and when used on a uk manifold everything else will bolt right up? Jamie theyre modified stock cartridges/housings so everything will bolt up. Thats why I bought them. As has been asked already, what mods would be needed to get these running. I have J-spec so assume UK injectors for a starters but what else is needed to get these running safely? Carl As above, BPU will run them but a better ECU will give better results. Link to comment Share on other sites More sharing options...
JamieP Posted April 11, 2010 Share Posted April 11, 2010 They seem a great buy. Link to comment Share on other sites More sharing options...
nr000001 Posted April 11, 2010 Share Posted April 11, 2010 PM sent. Link to comment Share on other sites More sharing options...
DaveR Posted April 11, 2010 Share Posted April 11, 2010 I wish this had come up a couple of weeks ago when I was staring at the increase in my bank balance and looking for stuff to spend it on! I'd have had these in a shot. Shame... Link to comment Share on other sites More sharing options...
Swampy442 Posted April 11, 2010 Author Share Posted April 11, 2010 All PMs replied, cheers for the interest Jamie they are good value, and for less than I paid, the import duty was 150 quid! I need the cash for the next project though Link to comment Share on other sites More sharing options...
pistonbroke Posted April 11, 2010 Share Posted April 11, 2010 I guess I'd have to buy another 1st decat pipe to fit these as mine is a jspec, if it wasn't for that, I'd have had these for sure. Link to comment Share on other sites More sharing options...
Kirk Posted April 11, 2010 Share Posted April 11, 2010 Would love to see this system properly tuned and in sequential mode! Someone buy them and get to it Link to comment Share on other sites More sharing options...
JamieP Posted April 11, 2010 Share Posted April 11, 2010 I guess I'd have to buy another 1st decat pipe to fit these as mine is a jspec, if it wasn't for that, I'd have had these for sure. If you need turbos for the sake of a decat pipe you would be mad not to buy these, if they perform like stated the car would be great i think, proper 500bhp and sequential:cool: im tempted myself, just put them on one of mine and see what its like. Link to comment Share on other sites More sharing options...
SupraJames Posted April 11, 2010 Share Posted April 11, 2010 Umm these would fit lovely on a UK car If only I had the spare cash Link to comment Share on other sites More sharing options...
ray007 Posted April 11, 2010 Share Posted April 11, 2010 Does anyone know if these would work on a jap-spec VVTI? Link to comment Share on other sites More sharing options...
Recommended Posts