L33 Posted March 11, 2010 Share Posted March 11, 2010 when ryan mapped the car it was set to 1 bar of boost on my defi gauge i done a peak check and it read 1.5, so i reset the peak and boosted again and again up to 1.5 bar. i have a blitz dual spec boost controller (2nd hand) and i turned what i think was the boost down, think its in psi so i turned it down from 32 to 18 and reset the peak again and it was boosting at 1 bar! great.....then i tried again 1.2....again 1.5 grrr, down to 16 which is what 1 bar should be and it happened the same. there is no units so im assuming its psi im turning down, thats why i dont it gradually as i didnt know what i was changing why am i over boosting? is it the boost controller not doing its job?! i dont want to keep on like it as it sounds like its spitting flames when im on full boost, hard to hear any thing with the screamer pipe which still scares the sh!t out of me!! cheers Link to comment Share on other sites More sharing options...
JamieP Posted March 11, 2010 Share Posted March 11, 2010 My money is on the crap xs power manifold/wastegate setup, few people have had over boost problems with them, sometimes the wastegate port is to small inside the manifold. Link to comment Share on other sites More sharing options...
RobSheffield Posted March 11, 2010 Share Posted March 11, 2010 Boost controller will only raise boost, not lower it. What were you mapped up to? If its safe at 1.5 thats ok, if not then its VERY bad. Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 its a tial 44mm wastegate? i was maped to 1 bar, but when we were going to try and fit the solaris we were going to raise to 1.5 bar Link to comment Share on other sites More sharing options...
RobSheffield Posted March 11, 2010 Share Posted March 11, 2010 You really need to sort it, could be very bad for the car. Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 whats the common reason for overboost? its never gone above 1.5 and considering we were planning to raise to that it should be a safe level? whats the worse that can happen? Link to comment Share on other sites More sharing options...
JamieP Posted March 11, 2010 Share Posted March 11, 2010 its a tial 44mm wastegate? i was maped to 1 bar, but when we were going to try and fit the solaris we were going to raise to 1.5 bar Not the waste gate itself, the waste gate exit pipe from the manifold, if the hole is to small it will over boost, might not be this but id say there is a good chance it is, i wonder if it was over boosting that killed the last engine that manifold was attached to? Geordiesteves engine failure? Link to comment Share on other sites More sharing options...
RobSheffield Posted March 11, 2010 Share Posted March 11, 2010 Need to check with Ryan mate, worst case is det leading to engine failure Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 well looking at it jamie, his engine was dry of oil when they stripped it, and the gt4088 which i recently found out was shot as that was the first time it was taken apart since it came off his car! and it was shot because the gasket used between the manifold and turbo was a twin scroll not open so the middle bit of the gasket looked like it came off and it was all burnt, which looked like it cooked the exhaust wheel of the 4088 Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 just seen the manifolds on whifbitz and there 1200!!! there has to be another option? it says T4 but i have no idea what that means? i have the BW 91 79 open turbo with 3" v band, 44mm tial ext wastegate and screamer pipe so what do i need to look for? this sucks Link to comment Share on other sites More sharing options...
RobSheffield Posted March 11, 2010 Share Posted March 11, 2010 You need T4, and no part of being single is cheap. Link to comment Share on other sites More sharing options...
Kev.O Posted March 11, 2010 Share Posted March 11, 2010 T4 is the flange size, which is the same as your BW turbo. Is your housing the twin scroll version (divided) Lee? Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 nope is open Link to comment Share on other sites More sharing options...
Kev.O Posted March 11, 2010 Share Posted March 11, 2010 nope is open The housing on the BW turbo? Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 i think so? i dont really know much tbh i just get told what to buy then order it is that what attaches to the manifold? the one i have now is open as i remember whifbitz asking is my manifold open or twin scroll and i had to phone the garage to find out which the xs power is and it was open has a 3" v band what ever that is? Link to comment Share on other sites More sharing options...
Kev.O Posted March 11, 2010 Share Posted March 11, 2010 i think so? i dont really know much tbh i just get told what to buy then order it is that what attaches to the manifold? the one i have now is open as i remember whifbitz asking is my manifold open or twin scroll and i had to phone the garage to find out which the xs power is and it was open has a 3" v band what ever that is? Yes that's right. Sounds like Paul got an undivided one. Divided: http://www.ardesign.info/catalog/images/S372%2080%20AR%20T-4.JPG Undivided: http://www.bullseye-power.com/images/turbopics/S366T-3SS.JPG Link to comment Share on other sites More sharing options...
L33 Posted March 11, 2010 Author Share Posted March 11, 2010 ah rite, yea i have a undivided i cant seem to find any where else to get a manifold? surely there must be another option than a 1200 whifbitz one? Link to comment Share on other sites More sharing options...
Kev.O Posted March 12, 2010 Share Posted March 12, 2010 No decent quality manifold will be cheap I'm afraid Lee Here's a few I've found: BL MVP PHR SP Whifbitz Link to comment Share on other sites More sharing options...
L33 Posted March 12, 2010 Author Share Posted March 12, 2010 http://www.blitz-uk.co.uk/images/products/productimages/hires/15059_P3.jpg thats my boost controller but i dont know which one of those readings is the one i have to try and turn down? think i been turning down the boost control? Link to comment Share on other sites More sharing options...
L33 Posted March 12, 2010 Author Share Posted March 12, 2010 cheers for that, looks like the whifbitz one is cheapest the bottom left of the manifold in the whifbitz link, why is there a pipe that seems to just stick out? compared to say the boostlogic one? be nice to have a manifold that every thing fits straight on, turbo, wastegate, down pipe ect so its a simple swap Link to comment Share on other sites More sharing options...
Scott Posted March 12, 2010 Share Posted March 12, 2010 Is a cast manifold not an option? Won't be a restriction till into silly BHP and the torque will be fantastic Link to comment Share on other sites More sharing options...
L33 Posted March 12, 2010 Author Share Posted March 12, 2010 whats a cast manifold? im liking the look of the boostlogic manifolds just need one i no will go straight on with my other stuff Link to comment Share on other sites More sharing options...
Kev.O Posted March 12, 2010 Share Posted March 12, 2010 cheers for that, looks like the whifbitz one is cheapest the bottom left of the manifold in the whifbitz link, why is there a pipe that seems to just stick out? compared to say the boostlogic one? be nice to have a manifold that every thing fits straight on, turbo, wastegate, down pipe ect so its a simple swap That's for the wastegate to connect onto. Looking at the BL manifold, it looks like it comes with a 4 bolt wastegate connection, which won't fit your tial wastegate if it has a v-band connection. Link to comment Share on other sites More sharing options...
Scott Posted March 12, 2010 Share Posted March 12, 2010 Its cast rather than tubular welded. Much much cheaper to buy but not shiney and pretty lol. Not sure at what level it becomes a restriction but I believe it is at least 600-800hp. Would be fine for your application I think they come in at around £300. I was planning on using one more so for the torque advantages. Link to comment Share on other sites More sharing options...
RobSheffield Posted March 12, 2010 Share Posted March 12, 2010 the bottom left of the manifold in the whifbitz link, why is there a pipe that seems to just stick out? compared to say the boostlogic one? Thats the wastegate port, optional which way they point. Its likely that could be the root of your problems on your car. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now