heckler Posted December 18, 2008 Share Posted December 18, 2008 Probably one for CW.. Its just started - occasionally when I use reverse I get a clunk/vibration from the back end, however, if i drive forwards it fine, and its deffo not the gearbox Link to comment Share on other sites More sharing options...
edge Posted December 18, 2008 Share Posted December 18, 2008 Does it do it when selecting first? Link to comment Share on other sites More sharing options...
heckler Posted December 18, 2008 Author Share Posted December 18, 2008 (edited) Does it do it when selecting first? its always been a bit clunky (6 speed) but you can actually feel the clunk/vibration when you reverse, like i said, drive forwards its fine. Edited December 18, 2008 by heckler (see edit history) Link to comment Share on other sites More sharing options...
edge Posted December 18, 2008 Share Posted December 18, 2008 Mine always used to clunk in when going from nuetral to 1st. I thinks its something that wears in the diff. CW has posted about it before. I will have a looksie Link to comment Share on other sites More sharing options...
edge Posted December 18, 2008 Share Posted December 18, 2008 http://www.mkivsupra.net/vbb/showthread.php?t=120948&highlight=clunk+changing+gear post 10. HTH Link to comment Share on other sites More sharing options...
heather1mee Posted December 18, 2008 Share Posted December 18, 2008 does it damage the car if left unfixed?? Link to comment Share on other sites More sharing options...
cheekymonkey Posted December 19, 2008 Share Posted December 19, 2008 Mine does this, thought it was pretty normal... Link to comment Share on other sites More sharing options...
Chris Wilson Posted December 19, 2008 Share Posted December 19, 2008 More description please, I would say it may not be hub bearings. Diffs are normally bullet proof unless James P is driving One for you, are the stock LED's in the dash removable easily? Got a car here where the heater knobs need a push sometimes to get the lights on, and the A/C button LED doesn't light at all. Cheers. Link to comment Share on other sites More sharing options...
heckler Posted December 19, 2008 Author Share Posted December 19, 2008 More description please, I would say it may not be hub bearings. Diffs are normally bullet proof unless James P is driving One for you, are the stock LED's in the dash removable easily? Got a car here where the heater knobs need a push sometimes to get the lights on, and the A/C button LED doesn't light at all. Cheers. Ok, if i drive forwards in any gear, no noise - works as advertised. come to a stop, engage reverse, clutch out and get a big clunk when moving backwards only, however if i put the clutch in or put into neutral while moving backwards, noise goes away. And as i discovered today, doesnt always do it! Yes, LED are quite easy to remove/replace - http://www.internetwork.org.uk/led/led.htm no idea where you could get replacements from, but more likely to be a dry joint. Link to comment Share on other sites More sharing options...
heckler Posted December 19, 2008 Author Share Posted December 19, 2008 Over the christmas period i'll get the back end up and see whats what... Link to comment Share on other sites More sharing options...
Dan8 Posted December 21, 2008 Share Posted December 21, 2008 mine does this & sometimes when i set of i get a vibration which judders side to side from the box just behind the centre console thought it might be the donut mines a non turbo with limited slip where can you get them from & are they hard to fit or is it a full shaft job Link to comment Share on other sites More sharing options...
Chris Wilson Posted December 21, 2008 Share Posted December 21, 2008 I don't know if it's even possible on the MKIV, but if someone was daft enough to fit the centre bearing upside down, so the prop had an angle in the mid joint, I am sure it wouldn't like it, and it would cause a judder. the centre bearing SHOULD be atop the mounting, up in the tunnel, not lower down. Next time I do a clutch I'll see if it's even possible to fit it upside down, it may just be so.... Link to comment Share on other sites More sharing options...
Dan8 Posted December 21, 2008 Share Posted December 21, 2008 i doubt is the wrong way i just thought it might be worn its similar to clutch judder after a thrashing but not if that makes sense Link to comment Share on other sites More sharing options...
SilverSoop Posted December 22, 2008 Share Posted December 22, 2008 Hmm...well I hope this is normal but when I engage reverse from a stop with the clutch in...I get a CLUNK noise from the back of the car but could be coming from the gearbox... Is this normal?? Link to comment Share on other sites More sharing options...
johnd-mkiv Posted December 23, 2008 Share Posted December 23, 2008 I had this with mine or simular it was the upper wish bone arm bushes knackered Link to comment Share on other sites More sharing options...
madwoody1 Posted December 24, 2008 Share Posted December 24, 2008 had this as well upper wishbone worn and rear tow control arm both sets of bushes where worn Link to comment Share on other sites More sharing options...
heckler Posted January 2, 2009 Author Share Posted January 2, 2009 well, no idea whats going on, but its stopped clunking! Link to comment Share on other sites More sharing options...
forester200 Posted January 2, 2009 Share Posted January 2, 2009 Do the wheels feel like they are crabbing at all , or one wheel feels like its locking a bit when reversing ? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now