Jim_1979 Posted August 6, 2008 Share Posted August 6, 2008 What you got there instead if anything? Any pics of what it looks like without the seats? I was thinking of removing them as they are not in the best condition and to be honest, it's not like anyone can fit in them!! Quote Link to comment Share on other sites More sharing options...
supra_aero Posted August 6, 2008 Share Posted August 6, 2008 was thinking the same thing incidentally. I know some people put a big bottle of nos in there. Quote Link to comment Share on other sites More sharing options...
tooquicktostop Posted August 6, 2008 Share Posted August 6, 2008 was thinking the same thing incidentally. I know some people put a big bottle of nos in there. Quote Link to comment Share on other sites More sharing options...
Pabs Posted August 6, 2008 Share Posted August 6, 2008 I was advised against this unless there really was a reason for doing so - they help to keep the drivetrain noise down to a minimum etc. Quote Link to comment Share on other sites More sharing options...
JustGav Posted August 6, 2008 Share Posted August 6, 2008 Sound deadening fabric tucked into the gaps... I've got a picture after I removed it all, will dig it out. Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted August 6, 2008 Author Share Posted August 6, 2008 Really? Surely it can't make that much of a difference noise-wise? Quote Link to comment Share on other sites More sharing options...
Jim_1979 Posted August 6, 2008 Author Share Posted August 6, 2008 http://www.mkivsupra.net/vbb/attachment.php?attachmentid=76700&d=1212872113 Sound deadening fabric tucked into the gaps... I've got a picture after I removed it all, will dig it out. That looks a bit extreme! Any ideas of how to make the rear decent if the seats are removed? Quote Link to comment Share on other sites More sharing options...
Pabs Posted August 6, 2008 Share Posted August 6, 2008 well - ask those that have - as I didn't really have a reason other than to lose weight etc - think Jay said not to bother. Quote Link to comment Share on other sites More sharing options...
JustGav Posted August 6, 2008 Share Posted August 6, 2008 That looks a bit extreme! Any ideas of how to make the rear decent if the seats are removed? It doesn't look bad when all the plastic side panels are installed to be honest, and that pic was during the strip out, it has even less now Quote Link to comment Share on other sites More sharing options...
supra_aero Posted August 6, 2008 Share Posted August 6, 2008 check big blue's car. As usual he had a stunning set up throughout his car. http://www.mkivsupra.net/vbb/vbpicgallery.php?do=view&g=1287 Quote Link to comment Share on other sites More sharing options...
JamesC Posted August 6, 2008 Share Posted August 6, 2008 Really? Surely it can't make that much of a difference noise-wise? Yep, it does. I had mine out recently when i had it sprayed and it was much nosier without the seats in place. Quote Link to comment Share on other sites More sharing options...
colsoop Posted August 7, 2008 Share Posted August 7, 2008 There is a neat little guide from Supraforums for tidying up the rear seat area if you feel inclined to remove them: (Quoted from source) Since I was preparing the car for a coming weekend race I decided to review the rules for my class one last time. When I saw "backseat may be removed, but must be neatly finished" I knew a rear seat delete would be in order!! But I didn't want to spend a ton of cash, spend too much time doing it, or need many tools to get it done. After a bit of thought, (well not much actually) I came up with this very clean, cost effective solution for about $20. You will need: 1 piece of aluminum or steel plate stock ~37" x 4" x 3/16" (or less) thick 1 piece 48"x 24" x 1/8" MDF, particle board, pressed wood..whatever! Carpet of your choice approx 48" x36" (there will be some left over) 1 can of sound deadener (optional) To start, I decided to use the existing back seat mount holes and fabricate a "brace". I found by using this brace, it provides a nice flat mounting surface for the board, and who knows, maybe it keeps some rigidity in the car the original seats were providing. 1) Take your flat alum. or steel material and put a couple of clearance holes (about 1/2" in size) 1" in from each end. That gives the holes 35" center-to-center. You may have to open the holes a touch to get them to fit, but it's no big deal. A dremel comes in handy for this. In the 1st photo, you can see I have it screwed in to the existing rear seat mount holes. 2) **OPTIONAL** Once your brace is mounted, spray back seat area with sound deadener. 3) Cut your board material to size. The sizes are : Top is ~39" wide and the bottom ~42". I bought my wood at Home Depot and it came in 48x24 size. Essentially, you are only cutting angles on either end of the board since the 24" height size is a perfect fit. It ends up looking like a parallelogram. Next, do the cut out in the bottom middle of the board. Make it about 15" wide and about 4" deep. This is so there's room for the transmission tunnel hump. You might have to take a bit more off to get a decent fit..again, a Dremel will do this in a blink. Here's a pic of my board. When test mounting it into the car, push it all the way up against the existing hatch area material. That way the bottom sits almost flush with where the seat edge used to be. Once you are satisfied with the fit you need to put the clearance holes to mount it to the brace you made. All I did was put the screws in their holes, place the board over them, and tap the board gently with a hammer. This will leave screw head impressions and give you a general idea of where to put your 1/2" clearance holes. 4) Cut your carpet. I left a couple of inches all around (you can see it in the above pic). I then folded it onto the back of the panel and used a glue gun to affix it. I didn't affix where I made the cut-out for the tunnel though. I just cut up to the board, and let it hang there...like a tongue or a flap. Don't forget to poke holes through the carpet where you put your clearance holes!! 5) All done. Just mount the panel over the brace and put the screws in to the existing seat mount holes. It's easy, tidy and actually looks really good. All for about $20. Here's a couple of pics. It does make a pretty steep angle and would be pretty much useless to store anything on it. But this was for racing, and I don't store much back there anyhow. Quote Link to comment Share on other sites More sharing options...
gaz1 Posted August 7, 2008 Share Posted August 7, 2008 some of mine, and yes it has been hoovered since then:d http://www.mkivsupra.net/vbb/showthread.php?t=144889 Quote Link to comment Share on other sites More sharing options...
Lebsteif Posted August 7, 2008 Share Posted August 7, 2008 I only removed the back part of the rear seats, that is the actuall heavy part. The lower part is just a piece of foam and left it in the car. Quote Link to comment Share on other sites More sharing options...
SimonG Posted August 7, 2008 Share Posted August 7, 2008 This is a pic of mine with rear seats out. Still needs some tidying up. Car feels much more spacious. Not much difference in noise. Glad i did it. Quote Link to comment Share on other sites More sharing options...
sidewaysdan Posted August 7, 2008 Share Posted August 7, 2008 i took the seats out much better Quote Link to comment Share on other sites More sharing options...
Gaz6002 Posted August 7, 2008 Share Posted August 7, 2008 i took the seats out much better than who? Quote Link to comment Share on other sites More sharing options...
sidewaysdan Posted August 7, 2008 Share Posted August 7, 2008 i took the seats out much better Quote Link to comment Share on other sites More sharing options...
SupraTTBPU Posted August 7, 2008 Share Posted August 7, 2008 How much kilograms are you lighter ?? Quote Link to comment Share on other sites More sharing options...
AlexM Posted August 7, 2008 Share Posted August 7, 2008 You seem to have a colour clash sire! I wouldn't mind turning my rear seats into a 2-teired storage area, keep the long flat pan for the boot (in case I ever put a bike in there..) and an area below for ICE / storage space! Quote Link to comment Share on other sites More sharing options...
edge Posted August 7, 2008 Share Posted August 7, 2008 http://www.mkivsupra.net/vbb/attachment.php?attachmentid=78508&d=1215618188 Inside sprayed black as it was silver and looked dirty Quote Link to comment Share on other sites More sharing options...
sidewaysdan Posted August 7, 2008 Share Posted August 7, 2008 You seem to have a colour clash sire! I wouldn't mind turning my rear seats into a 2-teired storage area, keep the long flat pan for the boot (in case I ever put a bike in there..) and an area below for ICE / storage space! i kinder like the two tone.im going to dye the capet black to Quote Link to comment Share on other sites More sharing options...
Chingy Posted August 7, 2008 Share Posted August 7, 2008 Heres mine Quote Link to comment Share on other sites More sharing options...
Guest CoolsBlue Posted August 7, 2008 Share Posted August 7, 2008 http://www.mkivsupra.net/vbb/attachment.php?attachmentid=76700&d=1212872113 Sound deadening fabric tucked into the gaps... I've got a picture after I removed it all, will dig it out. OMG what have you done to the front seat?!?!?!?! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.