123tom123tom Posted June 27, 2008 Author Share Posted June 27, 2008 right the turbo kit comes tomorrow, getting rather excited now, I am going to go with the T61 tub in the long run, with 650cc drop in injectors. i have a oil filter relocator and cooler also coming and a transmission cooler. my next purchase that i will be saving up for is the uprated gear box. i have also purchased some heat wrap, is there any particular way i should apply, or is it just wrap it up.... Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 19, 2008 Author Share Posted July 19, 2008 i am having a nightmare of a day fitting the oil drain , got it done now but there are two water pipes that get in the way that go to the auto box... any body else had this problem and if so what did you do to over come it. Quote Link to comment Share on other sites More sharing options...
paul mac Posted July 19, 2008 Share Posted July 19, 2008 i am having a nightmare of a day fitting the oil drain , got it done now but there are two water pipes that get in the way that go to the auto box... any body else had this problem and if so what did you do to over come it. there not water pipes mate they are the oil feed and return to the cooler, use an angled connector to the turbo oil drain and you can bend the auto box oil pipes out of the way (just a bit) make sure they dont rub or touch the turbo drain pipe or it could be bye bye engine and gearbox Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 30, 2008 Author Share Posted July 30, 2008 almost all sorted will be starting her up for the first time in 3 months..... crapping myself with excitement. Quote Link to comment Share on other sites More sharing options...
supra_si Posted July 30, 2008 Share Posted July 30, 2008 make a vid of the start up for everyone to experience pal Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 30, 2008 Author Share Posted July 30, 2008 will do just awaiting one key part hope fully sorted soon:) Quote Link to comment Share on other sites More sharing options...
JamieP Posted July 30, 2008 Share Posted July 30, 2008 Lets have some pics then:) Quote Link to comment Share on other sites More sharing options...
heckler Posted July 30, 2008 Share Posted July 30, 2008 no pressure - did my conversion in less than 14hrs - and it works... looking good chap. I couldnt be bothered with taking lots of pictures. Quote Link to comment Share on other sites More sharing options...
gaz1 Posted July 30, 2008 Share Posted July 30, 2008 no pressure - did my conversion in less than 14hrs - and it works... looking good chap. I couldnt be bothered with taking lots of pictures. well 1 finished one would be good:rolleyes: Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 30, 2008 Author Share Posted July 30, 2008 i have been waiting for bits here and there and still waiting for some bit now, ie intercooler/pipe work and 2nd decat..... but o just cant wait i need to start :) do i have to heat wrap the manifold or just the down pipe. I have heard that if you heat wrap the manifold it could put stress on it( it is XS remember) ps am going to need a mapper for the greddy emanage blue as well!!!!!! Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 30, 2008 Author Share Posted July 30, 2008 i have been waiting for bits here and there and still waiting for some bit now, ie intercooler/pipe work and 2nd decat..... but o just cant wait i need to start :) do i have to heat wrap the manifold or just the down pipe. I have heard that if you heat wrap the manifold it could put stress on it( it is XS remember) ps am going to need a mapper for the greddy emanage blue as well!!!!!! dont think ian c does it any more either (the mapping) shame heard good things Quote Link to comment Share on other sites More sharing options...
Homer Posted July 30, 2008 Share Posted July 30, 2008 After trying the EMB I absolutely recommend you rethink it as your choice on a single. At the very least you'll need an EMU, but ideally a full standalone. In the long run the standalone will be far more cost effective on a single, especially if you plan on taking things further, or refining the engine driveability. The EMB has no injector lag adjustment (amoungst other things) so for most aftermarket injectors it will simply not work. Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 31, 2008 Author Share Posted July 31, 2008 i am only going to use 650cc injectors and i have been told these will fit the stock rail with no resistor packs/direct replacement, i have been told as well as looking through this forum that the EMB will be sufficiant enough to cope with trimming 650's and running them fine. But again i am probably wrong? would it keep me going for a while a least well i save up for a stand alone Quote Link to comment Share on other sites More sharing options...
MarkR Posted July 31, 2008 Share Posted July 31, 2008 You're not having very good luck mate. I hope mine goes more smoothly. Haven't received any parts yet... Good luck with the rest of it... Quote Link to comment Share on other sites More sharing options...
heckler Posted July 31, 2008 Share Posted July 31, 2008 I know i'm bucking the trend, and i'm sure the experts among you will critisise me for this, but I run 720cc injectors with a resistor pack on an EMB. works fine for me Quote Link to comment Share on other sites More sharing options...
rick001 Posted July 31, 2008 Share Posted July 31, 2008 Good luck with rest of the build mate - good that you have done this write up Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 31, 2008 Author Share Posted July 31, 2008 Good luck with rest of the build mate - good that you have done this write up i think support is what i need right now cheers Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted July 31, 2008 Author Share Posted July 31, 2008 I know i'm bucking the trend, and i'm sure the experts among you will critisise me for this, but I run 720cc injectors with a resistor pack on an EMB. works fine for me so you have no probs mate, thats good to hear... who mapped the car for you? Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted August 13, 2008 Author Share Posted August 13, 2008 got some more work done on the car today, i installed 3 tranmission coolers for the auto box along with a transmission oil filter, slight problem when i took the bumper off i realised that it had no ducting where the smic used to be. I think am going to fit a spal fan in there too. Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted August 16, 2008 Author Share Posted August 16, 2008 getting there now!! just waiting for some final bits.... or and obviously need to sort that god dam emb out.... Quote Link to comment Share on other sites More sharing options...
MarkR Posted August 16, 2008 Share Posted August 16, 2008 Looking good bud. Keep it up... Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted August 16, 2008 Author Share Posted August 16, 2008 Looking good bud. Keep it up... cheers mate all comments are good at the minute:) Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted September 30, 2008 Author Share Posted September 30, 2008 front mount goes on this weekend, god its a big bugger. I have got a though though!!! i might have messed up slightly, i fitted 3 transmission coolers in to the space where the smic was, but now realise that the fmic pipework goes in front of where the air comes through to cool it. Kind of pointless them being there? any solutions come into mind from anybody, apart from shift them:) Quote Link to comment Share on other sites More sharing options...
RobSheffield Posted September 30, 2008 Share Posted September 30, 2008 What FMIC is it? Quote Link to comment Share on other sites More sharing options...
123tom123tom Posted September 30, 2008 Author Share Posted September 30, 2008 What FMIC is it? it is the Trust 4 row, i love it well worth saving up for;) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.