merckx
-
Posts
7641 -
Joined
Content Type
Profiles
Forums
Store
Blogs
Events
Downloads
Supra Articles
Gallery
Everything posted by merckx
-
Do they have all the premier league games on or do they just show sky sports and espn, what's the picture quality like? I found this one earlier. http://www.freefootball.org/events/20120218_2145_Vitali-Klitschko_v_Dereck-Chisora.html
-
That's quick. I had a look on their website the other day and you can even get same delivery,not cheap but a good service to provide. If you need anything diy then Toolstation are great and you get free next day delivery, minimum spend is only £10. Much cheaper than B & Q.
-
A cheap cheese wire cutter or strong fishing line etc.
-
GSS342 for a J-Spec, GSS341 for a UK
-
Where exactly did you look?
-
haha, very good.
-
Lovely cats, you can't help but smile when you look at the pic. Cats are adept at finding homes new homes.
-
Did you install them?
-
From an electronics forum I visitt, made me chuckle!
merckx replied to Chris Wilson's topic in Off Topic
lol Good for dismembering the bodies of those in rival drug cartels which I was looking at the other day. -
The offsets are lowish but I reckon they would be okay. Obviously you would need to use hub centric rings as the hub on the Supra is 60.1mm
-
I've had a look of my epc, it looks like the manual, auto, na and TT all use the same subframe. Like melloman has suggested I would ask Keron.
-
Two different numbers because they aren't the same part. The first one is listed as the SHAFT ASSY, REAR DRIVE OUTBOARD JOINT, LH The second is listed as SHAFT ASSY, REAR DRIVE, LH The parts diagram isn't easy to understand if you're not familiar with the driveshafts on the car, don't ask me. Can't you just go to Toyota and give them your vin number and let them decide which one to order, that's what I would do if I wasn't sure?
-
I'm surprised at that valuation, I thought it would be around 11K.
-
Yes, 5 year investigation by the police.
-
In other professions you could be suspended on full pay pending an investigation/trial. Capello should've kept his mouth shut, if he had any sense he would've realised that this could be the likely outcome.
-
It's the tank (I thinks it's red) at the rear of the boiler with the valve on it. I can't remember if you can get to the valve, it's a while since I've had the covers removed. If it's the 80HE or the 105HE Baxi it's all in the link I posted earlier, it takes ages for the pdf file to download.
-
For our boiler it says to open it whilst pressurising the system to 1.0 bar, it doesn't actually say whether to close it or leave it open after that. I normally switch the heating on to get the water pumping around the system, I then open and close the bleed screw until all the air has gone. I don't know if we're talking about the same boiler, below are the installation instructions for the 80HE and the 105HE. http://www.baxi.co.uk/docs/Baxi_Combi_Instant_HE_Installation_and_Servicing_Instructions.pdf
-
Combi boiler? The central heating pressure is down to zero, and you're having to top it up with the filling loop? You shouldn’t to have top the water up in the central heating very often at all. We have a Baxi combi, they recommend 1.0 bar, if it’s less than 0.5bar you’ll have problems. Do you bleed the radiators when you top up the pressure, on our boiler you also need to open the bleed screw on the automatic air vent whilst topping up.
-
Couldn't you have just used a black magic marker, far cheaper? Only kidding, I'm glad it's working for you. It's not nice when you start losing your hair, I 've gone through that to some extent.
-
Use the old cable to pull the new one through, they obviously need to go end to end to pull through properly, I normally use duct tape on things like this.
-
He's the BBC Formula 1 technical analyst! haha.. McLaren aren't likely to put anything worthwhile on display for everyone to see.
-
Well if it's plasterboard wouldn't it be easier just to use the metal detector type and look for the screws/nails that secure the plasterboard, even a cheap one will find metal. Once you've found the exact position of a few screws/nails going backwards and forwards with the detector it's easy to find the location of the studding. Or get one from Amazon and send it back to get a full refund when you're finished,it must happen all the time. Large companies like this accept returns without any hastle at all, free return postage and full refund. I haven't done this yet.
-
Their website has crashed.
-
If anyone's interested 11.00am Wednesday. http://www.mclaren.com/page/watch-the-launch-of-the-vodafone-mclaren-mercedes-mp4-27-live Posted already.
