tonyhawk

He got a witch for £116; sounds like a halloween bargain

I'd like to know too; my speedo and odo have stopped working! My car was imported from Japan about 5 years ago and I was the first UK owner; the importers did all the bits necessary for the the SVA and I've had it since. However about a week or so ago the speedo became intermittant and now it's pot luck as to whether it works at all! The ODO actually says 'miles' on the green readout, but the speedo seems to have an 'MPH' sticker on it, however I couldn't say if that was put there by the importers? I've had the entire dash off before now when I replaced the heater matrix and I don't think I ever saw a converter, but then I wasn't looking for one either. Would a converter add/change the word next to the milage to 'miles'? Any help would be VERY much appreciated. Ta.

Spec list updated with a couple of minor things I'd forgotten.

Cheers for that, it means a lot to me.

Interior pics added to original post

Cheers geez Ryan has done all of the mapping so far (on the original twins and the current single); the road tune is complete and it drives beautifully, the bit that needs finishing is turning the tubbie above 1.4bar. It has 65k on the clock.

Ta. It needs to be seen in sunshine for the full effect as it's a deep graphite, but with metallic flecks of copper and green. It was a complete strip for the respray (Piccy's), everything was off!

Good point, I'll have to find it....it's in a box somewhere... I might get Ryan to finish it, I'd feel happier to sell it on completed rather than 'it should do this...'

If you're looking for a new one, mine's available Beastie for sale

Ok, it has come to this and the beastie has to go It had a complete re-spray six months ago, engine rebiuld 3k ago and the valve guides a few days ago. The the main spec list is below, but what is not in the list is the Toad alarm with total closure and tracker unit. I'm sure there are lots of things I haven't remembered, but I'm happy to answer any and all questions I'm looking for £14k. In the spirit of complete honesty, there are a couple of things that are not 100%: the wheels are not perfect and two of them have some surface corrosion that needs treating; the only other defect is on the bonnet, which has two cracks at the front; I wanted to get them sorted, but I haven't been able to find a good body shop that can work with CF. To get both issues sorted would probably be about about £500ish, which is why it's not priced as high. Piccy's attached. Spec: Block: JE Pistons Bottom end lightened & balanced ARP Stud bolts ARP Rod bolts PHR Oil pump Cylinder Head: Polished/Ported/Gas Flowed Crower titanium valve springs & retainers HKS Inlet and Exhaust Cams (264 degrees) HKS Cam Wheels New valve guides Turbocharger, Induction & Cooling: Garrett GT358466R (not the GT35R, this has a bigger induction impeller) Boostlogic oil kit HKS Wastegate with screamer pipe Apexi Induction Kit HDi Intercooler HKS Dump valve ASI rad Fuel, Tuning & ECU: AEM EMS with 3.5 Map & Boost solenoid HKS DLI SARD 800cc Injectors SARD FPR FPD Bypass NGK BKR8 Plugs Bosch 044 fuel pump Exhaust: Reworked, re-welded and ported XS Power manifold XS Power downpipe XS Power midpipe HKS Superdragger rear box Drivetrain: RPS Flywheel RPS Street clutch Suspension, Wheels, Tires & Brakes: BBS 18" rims Yokohama AVS Sports (245 Front, 275 Rear) Engine Dress: Shiny Inlet Manifold Shiny Plenum Chamber Shiny Water pipe Shiny Fuse Box Cover Greddy Alloy pulley set Greddy top rad hose Greddy bottom rad hose Shiny coolant expansion tank Painted spark plug cover (same as car) Painted strut brace (same as car) Exterior: TRD Carbon Bonnet TRD Carbon Wing Top Secret front bumper Toyota side skirts Veilside wing mirrors Extras/Gauges/Toys: HKS Turbo timer AEM Wideband Sensor Defi Display with Exhaust Gas Temp, Oil Temp, Oil Pressure, Water Temp & Fuel Pressure sensors Performance: Mapping (by Ryan.G) was aborted due to a faulty oil line, a boost leak and some oil burn, which was preventing enough advance being added. However, in this unfinished state it still managed 533fwhp at 505ft/lbs All of these problems have been sorted (the oil issue was valve guides and have now been replaced), however I haven't taken it back to Ryan to be finished yet, but it should see 600bhp.

Ta No probs

I'll be selling mine soon, but It'll be up for c.£13k Piccy's and specs here Tony

Trying again!

Oops, that didn't work, hang on....

Interior piccys