Harllequin

Bugger, give Kevin a slap then. I'd have been up to your place on Wednesday to get em LOL Thnaks for the reply though. Much apreciated.

Ordered the Hoses and the plastic bits for connection to the coils. All should be here on Wednesday am. I can feel a day off on the cards!!!

The best price I have seen for a new one is £500. I'll be after a second hand one I think. Cash being rather tight and all!!

Still looking for one. Anyone pls

Rang you Monday and you didnt have any but you were going to order some in. Rang again in Wednesday, spoke to Kevin who said if I was having bother getting them from Hodgson then you would not have been able to get them either. At which point I gave up and decided to wait. I do need 2 crankcase hoses, Toyota part number 12263-46010 & 12264-46010 I think. Not ordered them yet from toyota, would you happen to have those in stock Gareth?

Went down there during the week. Tried tyre spot too. non of em had anything that would fit.

Well thats the FCD fitted, Waldro fitted, Plugs done, already had the boost guage. Stainless is on, Second cat is out, First cat is off, NO studs broken in place!!! However they were totaled. Must have been put in my a sumo wrestler as ther threads were shot. Stuck now coz I cant get the 3 studs and nuts Ordered them last week. They said they would be in mid week. However they cant get em and apparently it will be mid next week at the earliest. Role on next week end now then.

Looked at that wireing again and looks like that is the correct location for the wires after checking another wireing block diag. Also that other gubbins is a KPH/MPH conversion module. Happy now I'm not going to go bang, melt or take fire

Brilliant, thankyou.

Hay guys, yet another question. My front Decat tube section has a 6cm (2.36 inch) diameter, the restrictor ring I have has a diameter of 5.7cm (2.24 inch) Will this be enough of a restriction to limit my boost below 1.2bar. Thanks to all of you technically minded folks out there!!!

Hay there again guys. I'm going to fit my decat, however there is no provision for a gasket. The 2 faces however are flat as seen in the attached pic. Would it be ok just to use exhause assembly past as a gasket, or should I look for another option. Any advice welcomed. Darren

Not taken the car out yet for fear of wire melt down. Can anyone confirm that what I've wired would be correct please? The car starts, but I've not driven it any place as yet. Cheers guys

Should have taken a pic of its insides while I had it to bits

I opened it up, but it gave no indication on the inside what it could be. That was the inside of the box.

Hope so, coz thats the way its locked in now

Looking at it I think that: - Green (P) should go to the black/yellow striped wire just left of the pin blank on the bottom right of the 2 block picture. Black (E) should go to the orangy brown/metalic fleck in the middle of the 2 pin blanks to the bottom left hand side of the right part of the 2 block picture. Red (B) should go to the black/red striped, metalic fleck in the last bottom right wire of the single connector block.

Hay there guys. Before I go cutting and joining wires I'd just like to clear up a few points with you if I may. I have a Greddy Boost Limiter Cut Controller. I'm using this guide: - http://www.mkiv.com/techarticles/bcc/bcc_install/bcc.htm However when I look at where to wire into I have the problem that the diagram does not seem to match up. For example Green to To turbo pressure signal wire marked 'P' on ECU diagram(BLACK/YELLOW STRIPED WIRE) On the diagram this is shown as the second wire from the right at the bottom, however on my ECU the black / yellow striped wire is actually the first from the right. there is however what would look to be a pin blank to the right of the wire as shown in the picture. Also in the guide there are no colour codes as to what wire colours to wire the black and red wires into. So can anyone please give me a clue from the picture which wires i should be splitting into for the red and black please. Lastly I have a box gubbins already added into my wireing. and I'm thinking it is something to do with the english speedo concersion, however the ABS and HIPS thing has me confused. Please help a poor confused lad!!! Cheers in advance guys.

Could I get some sizes of tyres and pics etc please? Cheers Darren

Edited thanks m8 Can you tell Chelle bought me a bottle of JD last night

Bought, what a star!!!

Hay there guys. Any of you got any wheels n tyres to the following specs. 18" 9 or 9.5j 114.3 PCD with as close to 50 offset as possible. With min 165 at 35r18s inc some reasonable tyre life left. 18" 8j 114.3 PCD with as close to 50 offset as possible. With 235/40R18s inc some reasonable tyre life left. Sorry to be so specific as beggers can't be choosers and all that. But it may save you guys waisted PMs. Cheers in advance Darren

Hi guys, I'm after a front decat and resistor ring for my 93 TT From what I can tell it has the second cat out and a 32 stainless fitted. Cheers Guys Darren

Any update on progress? Keeping my fingers crossed for you!

It was a guy local selling some second hand wheels n tyres. I'm going to leave it though. I dont want thinner then stock at all.