123tom123tom

can a borrow yours mate, if possible, it would be much appreciated.... i love this forum for this type of team spirit. cheers, can i have the email address as well then i can by one if it works:)

that would be great mate, let me know if you find it or not, at least if i do borrow yours i can find out whether it is the laptop or the cable, right?:):) you have just give my day a pick up:p

where do i gat on of those cables mate.....WHERE A NEED ONE:taped: seriously though it just would be nice to set everything to 0 to create a base map so i could get the car to be mapped. i started it the other day and filmed the start up, but the car ran rough obviously because the emanage unit used to be on a honda so i have been told. i need to reset but cant do it because of this problem.

is it possible to split as i am after the 2nt decat, if so how much:)

am stuck with this one at the minute. I think i might leave this aspect for a while and get other stuff done. Like fitting the 3 transmission coolers and filter.

is there anybody near me that actually maps these things so i dont have to mess with it full stop. the conclution is i buy a new greddy cable and a new laptop with the serial port and hopefully this will solve the problem.....

the unit was second hand and bought from ryan g on here so am guessing it should be fine.... it still connects to the emb, well it says it is online when i plug it in. when i plug it in it asks if i want to create a emb data connection, i said yes it searched for the drivers on the software disk, then said sucessfully installed then the unit sorftware said online, when i pull the cable out it says offlie so i think it works?????think????? plus my laptop doesnt have the 9 pin serial port on it. its all going wrong!!! what next please help am becoming depressed about it

i have just tried doing what you said, but the light is on but know one is in:blink: it says it is online and the E in the top corner of the software is flashing green, but when i try and import it just does as i said earlier in the thread. It says corresponding in progress, or something along those lines but does nothing. the loading bar doesnt even start, i got the update off the web for the firmware v1.39. I went to the update main unit and it looked for the file i downloaded, it found it, brilliant, went to upload it to the main unit and it failed. what am doing wrong:taped: i have a pic of the cable attached(i get connected so i cant imagine it is this) i did all the jumper settings inside aswell to what is correct for a supra.... if that helps

yes i believe it is the genuine cable, looks like the one on there website for advertising, when updating the unit can i just down load a update from some where onto my laptop or does the laptop have to be hooked up to the emb to do it. ps my version was 1.11, i have updated it to 1.13/1.39 firmware i think that is correct. dont think i can version any higher that that with out a original 1.20/1.40 cd

does this importing data normally take a long time, its just i think i did that but maybe didnt give it a chance to import:) i get the message corresponding and a load bar but nothing happens, unless like i said it takes a long time. i will have to give it another go, should the ignition just be turned to the last click before starting so that the EMB is on obviuosly

right i fiited the EMB today in the glove box, all went very well and all fits perfect will post some pics of he install tomorrow, have a question, i hooked the laptop up to it via usb connection, how do i find the map that is on it at the minute. what is the process of loading it up. it says the status is online when i connect to the correct port, i dont know which options to use, i want to create a base map so i can drive it somewhere to get it mapped properly. any idea's guys;)

might be aircon bleed valve:search:

cheers matey thats great stuff, that article on setting it up is spot on.

right i have a number of questions in regards to this EMB:) 1. the unit itself was bought second hand off Ryan G, i believe it used to be on a honda not 100% though, is there a way of resetting it to factory? 2. sorry about the quality of the pick in regards to this next question, but the side of th EMB has some little twisty dial things, they are currently all set to '0' should they be set to anything different. 3. What do i connect the what i believe to be a boost pressure sensor too, can some one confirm that is what it actually is. (could it be put to the pipe that comes directly out of the back of the intake chamber. 4. inside it has lots of jumper settings do these need to be changed as it has been on a honda. any help is appreciated here.

so you have no probs mate, thats good to hear... who mapped the car for you?

i think support is what i need right now cheers

i am only going to use 650cc injectors and i have been told these will fit the stock rail with no resistor packs/direct replacement, i have been told as well as looking through this forum that the EMB will be sufficiant enough to cope with trimming 650's and running them fine. But again i am probably wrong? would it keep me going for a while a least well i save up for a stand alone

dont think ian c does it any more either (the mapping) shame heard good things

can you get me all the detail plz for the coolers and the kits:) cheers

Hope Jay dont mind me posting this, please ignore the dodgy filming i was trying to film over the crowd... it is i think his first run at totb:)

yeah thats the one lol:p

no my partner, she has a thing for a dirty rugby player:p

this is me, the only pics i have lol posing after rugby game:rolleyes: so gay that pic then me and my daughter:) she had just got that buggy for christmas:)

i have been waiting for bits here and there and still waiting for some bit now, ie intercooler/pipe work and 2nd decat..... but o just cant wait i need to start :) do i have to heat wrap the manifold or just the down pipe. I have heard that if you heat wrap the manifold it could put stress on it( it is XS remember) ps am going to need a mapper for the greddy emanage blue as well!!!!!!

will do just awaiting one key part hope fully sorted soon:)