Jellybean

Cool, will get her on the ramp again and see , it's hard to tell listening as the diff was rebuilt so it maybe something else but when we tested it on the ramp we had no issues...tricky one

Thanks but no speed converter is required on mine , she has a sard analyse rom in the ecu so the delimiter would not be an issue

Did not touch the throttle side, but it is my next point of call this morning, maybe something is loose This only started to happen after I was able to give her a good spirited drive of the year

Not too sure , mechanic put it on

I installed a new OEM Prop centre bearing, do these need to bed in; you can hear it wizzing around , on throttle She was copper greased up prior fitting

She is a manual 6 speed , Slip Cont off flashes after some WOT , I have not yet done a quiet drive yet The light will keep flashing very 2-3 secs Car is just back on the road , there are no error codes, I did reset the ECU; in the morning when I start her she is fine until I do a WOT Things done to the car Rear wheel Bearing Both rear Abs sensors disconnected and reconnected Rear diff rebuilt and installed Prop carrier bearing New Rear brake discs Any idea's, recheck the ABS sensor connections?

In the next video , can you please get the sound of the T51 Flutter

Hopefully Paul will comment I reckon she is gone , might get a TRD diff Wondering if I put in a new diff will I need to replace all the parts again? ·90366-54014 side carrier bearings x 2 ·96721-31110 side carrier cover o rings x 2 ·90311-45013 axle seals x 2 ·00295-01281 FIPG sealer

Thanks Dude, was just wondering as I just did mine Did not know if I should expect a few KM of bedding in Car sounds and looks great, I would not bother polishing the Turbo Looks great as is

Anybody ? Anybody ever in the the Time attack whifbitz Supra's, they ran a carbonetic diff

Very nice! Great sound off her; when you got your wheel bearing done , did you need to bed it in?

Just need some help with something stupid I am doing , probably take a dev a few mins to work out https://ecommerce.shopify.com/c/shopify-discussion/t/help-with-variant-images-268105

Had the LSD rebuilt , just drove her 13KM; but she is very noisy, best way to describe it is , as speed increases the diff noise increases but it loud enough to imped listening to the stereo at a sensible level, you can hear the diff turning , it is though there is no oil in it ; similar to the video below I had an aristo diff in her the last 12 months and she was quiet Its hard to explain, but do I need to put a few KM on her to quieten down? LSD: Carbonetic (Has at least 100.000 KM on her) Oil used: Motul PA 90 LSD Rebuilt ·90179-28006 pinion nut^ ·90311-50018 pinion seal^ ·90366-38009 pinion bearing^ ·90366-50039 pinion bearing^ ·41231-14110 crush sleeve^ ·90366-54014 side carrier bearings x 2 ·96721-31110 side carrier cover o rings x 2 ·90311-45013 axle seals x 2 ·00295-01281 FIPG sealer

Thanks Damien!

Is it this part number? 90183-03092 http://www.toyodiy.com/parts/diag_1x38yYS.png

Hey Put in aftermarket front speakers so need to grommet near the speaker grill won't fit unless you trim it and glue to the door card Q: where can I get one, tried halfords but no luck

thanks Mark

Hey Does anybody know the OEM settings?

Looking at Toyo Diy , you have to buy the whole door car to replace the plastic cover for the door switches? Central locking, electric window area Anybody buy it separate, I tried plasti dip on it but I am like a gymnast trying to get out of the car in the carpark, my foot/knee keeps rubbing off the panel and has already scuffed the plasti dip

Hey My valve covers needed to be tightened up, last touched a few years ago Is it just as bad to over tighten , will they leak ?

http://www.greenline.jp/ are also good, I generally just go with who is cheaper; got parts from both companies Nengun shipping rates have gone crazy so stopped shopping there

If anybody needs wheel bearings front or rear kits, these guys do a huge saving over Toyota http://www.brt-bearings.com/aboutautomotivebearings.html BRT1431 rear bearing kit is @ £23.76 pound sterling each Hi BRT1431 – ex stock, @ £23.76 pound sterling each Best Regards shannon Ball, Roller & Transmission Bearings Limited Tel: +44(0)1945 474655 Fax: +44(0)1945 474186 http://www.brt-bearings.com Online Shop http://webshop-cdn.tecdoc.net/brtgroup1/home.jsp

Price : 35 gbp Description 48818-14050 BUSH, STABILIZER, REAR 48815-14080 BUSH, FRONT STABILIZER BAR, NO.1

Theres a reason many hyper cars and OEM manufactures use Bilsteins, I was around the tack in Damiens Supra with the CW setup; car was like a go Kart and I was shocked how comfortable it was , soaked up the bumps

I got the last of the TRD rear subframe bushes and front pre-facelift upper arms and lower rears