Jellybean

Not too sure , car looks vaguely familiar Hope the guy is ok!

http://www.belfasttelegraph.co.uk/news/northern-ireland/pictured-horrific-belfast-york-road-crash-one-man-seriously-injured-35207455.html

I saw a few of the new lexus RC Models on the road (BMW 4 Series coupe rivals), look stunning ; the Lexus LC to me looks like a modern day Supra , V8 powered In the flesh I reckon the LC model is jaw dropping impressive

I would also drive a BPU , makes a big difference , nearly an extra 100hp for very little outlay

Thanks!

You edited the part number

I asked Keron / TCB they said LH 81560-14700 was only available as a Lense no loom I ordered mine off Toyota Ireland because they said they are available , got it Friday and the LH 81560-14700 had no loom

Think I am looking at the Jspec numbers , sorry forgot I was using my VIN It is the lense without the boot lock hole , depending on if I am looking at the car from the rear or the front the lense can can be RH or LH LOL What is

Yes , 81555-14660 RH ; I was talking to you yesterday , replied this morning Think you only have JSpecs

I tried to buy the loom , its discontinued

Hi You cannot get the complete Lense and Loom (81551-14660) LENS, REAR COMBINATION LAMP, RH anymore I bought the Lens and tried to buy the Loom separate (81555-14660) -- this is discontinued Question: Is the Preface lift loom interchangeable with the Facelift lenses ?

Project Paparazzi -- we know how good you are at taking photos

Thanks! Was looking everywhere for the answer I would tap the bolt on there but I dont have the tooling , 16 euro is not bad for the bolt

AS I have a 93 Think I found my answer http://mkiv.com/techarticles/oil_sensor_mod/index.html 90401-19008 Union Bolt 90430-20016 Gasket 90301-68005 O-ring (Optional) Supra 1998 / 2001 Lexus IS300 Setup Solution It is a pita to use a T bolt on the 93- 97 Supra, as the pressure sensor is screwed into the block behind the AC compressor. The Lexus IS300 & 98 Supra run the factory pressure sensor on the base of the union bolt connected via the Oil filter housing , easy access It is as simple as removing the stock union bolt and replace it with the Lexus/ Supra VVTI bolt, The new OEM bolt has a 1/8 NTP sensor port Supra 1998 / 2001 Lexus IS300 Setup Supra 93-97 Setup

Wez, I was looking at doing the same , did you get the Lexus Union bolt in the end? I want to remove the Relocation kit and install the Oil filter back on the Block as per OEM , I will loose my pressure 1/8NTP port Was thinking of getting a Lexus Union Bolt , not too sure of the male port on this ? 90401-19008 Union Bolt http://mkiv.com/techarticles/oil_sensor_mod/index.html

Thanks

What is the thread fitting on the Supra 3/4 UNF Mocal Sandwich Plate 571-SP1 http://www.speedflowshop.co.uk/mocal-sandwich-plate-571-sp1-1019-p.asp

Mike sorry can show me a picture what the two way adapter looks like? Where is the stock oil pressure location for the oil sender and stock sensor

Hi I want to remove the Oil filter relocation kit but retain my 1/8 NTP oil pressure sensor Question Can I fit a Sandwich Plate to the oil cooler assembly and still get an oil filter on, looks a bit tight? Sandwich Plate with Thermostat , I was thinking Mocal Thermostatic Sandwich Plate 571-OTSP1 with a 16 UNF http://www.speedflowshop.co.uk/mocal-thermostatic-sandwich-plate-571-otsp1-1020-p.asp

Nankang NS-2R might be worth looking into, and the Federal 595's

Not too sure how much they used , Some companies do Dintrol kits http://www.flatdoguk.com/rust-proofing-kit-large---new-vehicle~1415

I had mine done recently and they covered the underneath in Zinc prior to sealing , as Nic said , use an industrial heater , once the Zinc is on , she wont rust http://www.bardahl.nl/en/product/72104-zinc-primer-en/

Try get some Photo's, what M5 diff is it, Variable locking? Recent M diffs have electronic motors tied in with traction control? What ratio are you using?

Nice Project , be interesting the work required to get the Diff to fit