Jellybean

Thank You

Thanks , sorry missed that link

Was wondering what make of material it was

It is I asked on facebook but dont want to bother him too much , if he is busy

Hey 2JZGTE Jspec BPU, Fuchs 10W60 Oil, Installed 264 Tomei poncam's ,in the car about 600 miles ago ; they have developed a ticking noise when hot , on idle and runs in tandem with rpm They where dialed in as per Tomei spec, silent in operation or as per OEM on installation , pre/post mapping and for about 500 miles after Unorthodox racing pulleys , locking nuts are still all secure Common cams need re-shimming after run in? Will take the covers off the weekend to check , what should I look for? Parts fitted at the same time TBELT -- Gates racing Kevlar OEM TENSIONER ASSY, CHAIN, NO.1 OEM IDLER SUB-ASSY, TIMING BELT, NO.1 OEM ABSORBER SUB-ASSY, BELT TENSIONER ATI Crank Pulley Billet Tensioner Bracket Billet Aux pulleys fitted & idler Billet upper Shock arm

Anybody know the materials used to make the box over the clutch master cylinder https://scontent-ams3-1.xx.fbcdn.net/v/t1.0-9/14358966_1392096860819677_2868573951974854510_n.jpg?oh=e993e1c48bd869fbab254c77c720d532&oe=58CDC43B

Could be , cannot find a pinout for it

Does anybody Know on the Jspec , what Pin corresponds to the OEM TRAC light (Slip Cont)? Nothing looks obvious on the Pin outs, OEM Harness http://www.mkivsupra.net/vbb/showthread.php?35919-ECU-Pinouts/page2 http://www.mkivsupra.net/vbb/showthread.php?252809-Facelift-ABS-ECUs-pinout

Found it https://docs.google.com/viewerng/viewer?url=http://www.mkivsupra.net/docs/repair/DI.pdf

Thanks, found it buried under stereo wiring ,

The unit has ABS written on it , but the part number references a/c heater control unit ; I am a little confused , where is the loom for the wheel speed sensors?

Thanks Lee , this is non VVTI car GTE 1993; it has 3 orange blocks, with any schematic we look at does not reflect the same pin count

Down setting up the TC,I have printed out every single schematic I could find and nothing matches Looking for speed sensor pins 88650-14270

Thanks , was just curious , after I saw this setup https://scontent-ams3-1.xx.fbcdn.net/v/t1.0-9/15032310_10211236702852739_7511255294269147227_n.jpg?oh=f33683631c6ba4afd1d591f7f26cd73c&oe=58C4C112

Not for the same purpose? If not,Why measure one over the other?

Thanks

Handy http://www.rhdjapan.com/oemrequestlist/oemcatalog/category/brand/toyota/vname/SUPRA/vid/108

Thanks , in comparison to using Wideband sensors , why use one over the other , cost?

Thanks , yes , why use a temperature probe in a exhaust or inlet manifold

why use Thermocouples in a manifold?

I have Cat 5/6 Ethernet ports wired in all rooms , alot quicker than using copper

powerline kit? Running over copper wire?

Thats how clifford works to prevent you leaving your car in gear with remote start activated

Hi Virgin Media box I have some bad connectivity spots in the the apartment , each room has an Ethernet port , was thinking of using an extender in the Bedroom and run it off the Ethernet access point , setup a second network , the device will use the network with the best signal I dont have a spare router knocking around Was thinking BT 11ac Dual-Band Wi-Fi Extender 750 Kit OR NETGEAR EX3700-100UKS AC750 Mbps Any advice?