Jellybean

That looks like Simons one in his R33, I was driving his car and it felt/looked alot nicer than the Nardi He thinks it is 300mm when I asked him, must measure it later but I am a bit of a whore for Sparco!

Thanks, I will try and see if I can try one. Think my friends keys racing is a 300mm one

Thanks Dunk, I was putting in 36 after a 30min run to the Garage , I will drop to 34 I got new tyres the weekend and the fitter said I should be running 30, I said toyota told me 36 , he siad a range rover runs that. Thats great but my car is a Toyota Supra! From what I can see my rears are wearing evenly, my fronts however are not bad for 5 years but I am getting the tracking checked

Might as well resurrect this thread Does anybody know what Steve and Paul Whiffin run in time attack; I am sure they will know the correct pressure after all the laps they have put in! Nic, do you have the Toyota Service Data for the Alignment ; the image got cut off thanks! (maybe make it a sticky)

They are close to a 1000Euro,if not more! I have the Nardi TRD wheel just fancy a change I am going to buy another quick release so I can use either wheel The Nardi could do with new leather I dont know if 300mm is far too small

Anybody recommend a steering wheel, I was thinking a 300mm Sparco : Sparco 300 Steering Wheel Black Suede - 300mm http://www.demon-tweeks.co.uk/performance/steering-wheels/sparco-300-steering-wheel-black-suede-300mm http://www.demon-tweeks.co.uk/oncirrus/3/images/product/enlarge/spa_p300-steering-wheel.jpg

Thanks!

Cool thanks , didnt know that just taught they sold them!

is that near the pollen filter

get you! why does this quick release system have two wires? It seems to be common It is the same in my polo the Horn Button completes the Circuit , the two wires confused me

Cool thanks guys, I have an spline Quick release on just want to upgrade to a ball lock system but the Ball lock system has two wires , Red and Black The Odula (spline) has just a red wire, so if I just connect one of the wires , on the steering rack and one on the Wheel , all should be good?

Hi does anybody know where I could get a replacement Nardi center ring cover https://lh6.googleusercontent.com/-ZvEfKlDsPU8/T7qzh9iANqI/AAAAAAAAAmo/M4xaOdzLbZ4/s776/20120521_184234.jpg

Hey How do I fit a quick release to the Horn, it has a Live and ground but the Horn just has a Live http://www.rhdjapan.com/media/catalog/product/cache/1/image/5e06319eda06f020e43594a9c230972d/18856/Image/Normal/Image3.jpg https://lh6.googleusercontent.com/-gsX7uDDmedc/T7qzhn3Zi7I/AAAAAAAAAms/iuEm6RgAlu4/s776/20120521_184058.jpg

Both 2011 and 2012 look awesome, Work Meisters are really starting to grow on me!

Looks awesome Marc, Is that Ibrar's Low Level spolier you are running?

Looks a bit like the LFA at the front? What happened to the rear Lights look awful! Bring back these!

Pig, I am trying to get SRD or Whifbitz to make up a Kit for the Supra! Maybe Chris would like to? http://www.mkivsupra.net/vbb/showthread.php?263217-Group-buy-ideas/page14 http://www.mkivsupra.net/vbb/showthread.php?250640-SRD-New-Products-and-suggestions/page8

Chris If I was to change all my Vacuum hoses would you recommend the Hose Techniques Kit?

Did ryan say he going to do a plug and play version you could install and he could check remotely? Save him coming over to Ireland for example?

Thanks! Sorry Last Q, what is the Calculation to get Wheel hp

Awesome cool thanks Malcolm

What about a kit similar to Hose Techniques Kit http://www.hosetechniques.com/index.php?main_page=product_info&products_id=1993 This kit contains all the Silicone Vacuum hose needed for your application in the correct lengths required for a total of: (32 ft Total) Also included will be all the extras such as tie wraps, tools, fittings (when applicable) and instructions for FREE! Each hose in your kit is of the correct proportion, both in length and wall thickness (you can rely on HoseTechniques to have determined the appropriate wall thicknesses for each hose provided in your kit). The color and gloss of our hose will provide a brilliant look to your car engine, and our guarantee provides the confidence that you are installing the highest quality silicone available, designed to eliminate the problems caused by deteriorating* OEM rubber hoses. (*You probably already know about the fact that poor quality hoses can severally affect the performance of your car.) Suggested Uses - Suggested Hose I.D. Sizes* Intake Manifold (small fittings) - 03.5mm Boost Controllers (Greddy, HKS & other) - 03.5mm, 04.mm or 06.0mm Windshield Washer Bottle - 04.0mm Intake Manifold (small fittings) - 06.0mm Radiator Overflow Hose - 06.0mm or 08.0mm Hood Hold Up Rod - 06.0mm or 08.0mm Intake Pipe (large fittings) - 08.0mm (includes aftermarket intakes & some radiator overflow) Misc. covers of hard lines, etc. - 10.0mm (refer to Slit ‘n Groom™ Technique in instructions)

Nigel did get his dyno'ed at Thor Racing too and it was around 435 , not 100% what they use though but from readin on here they are accurate for readouts

Mine was 310 on a Dynapack hub dyno with a boost leak and leaking oil cooler Nigels on the same day (UK spec Supra) was 425. Regardless of figs a Dynapack hub dyno is wheel hp? and Malcolms 455.5 is wheel hp I presume?

It is an abnormal size, my optima sits in nice and snug Length:256 mm Width: 174 mm Height: 200 mm