Jump to content
The mkiv Supra Owners Club

DAVE-W-

Followers
  • Posts

    49
  • Joined

DAVE-W-'s Achievements

Newbie

Newbie (1/14)

1

Reputation

  1. I know more about cooking than i do about mechanics and thats sayin somethin so i aint touchin the car. Its a combination of boost issues, idle issues, smoke issues.......... Thats why i just want to give it to the right person (with a blank cheque:faint:)to sort it. No hassle just results
  2. Cheers for that Alan. I get the impression on here that CW is one of the most knowledgable guys there is. Hes closer than Whifbitz so if people say hes the best il go there ( Was hopin for Envy cause its close:p) but the journeys worth it to get car right
  3. From memory i think Geo uses west coast customs in irvine but as to whether they are supra specialists i dont know
  4. Its the same old story. One problem fixed another develops. The supposed japanese specialist garages im using have no focused knowledge on supras. Its gettin to the stage im considering puntin the car but id rather try and get it fixed one last time. I just want the """BEST""" person to sort it. Is Envy one of my best options from Glasgow? If i have to travel far tho to get the best i will and ill pay for the best. Just need it fixed b4 i have a mid life crisis and get a 3 series Please no random garages down backlanes that you know a guy. Im after the best person i can get with the facilities available to fix it. There must be somone renowned as the best Much appreciated Dave Wilson
  5. Ok cheers nigel. If 275 is an option then id probably go for that. The supras a wide car so 275 would also look better suited from the back. Cheers porky for suggestin camskill. there the cheapest ive seen at 265 £93 275 £116
  6. Grip is an issue Paul. A cheap 265 has more grip than a cheap 255 Only £10 difference between a shit 255 and 265 as opposed to far more £££ for a quality 255. Id say im a genius
  7. So from what your sayin 265 should be the largest as 275 will overhang and seems to have caused issues for people. I found some nice cheap falkens 265 fk-452's for £110. Not wantin to spend alot so theyd do Cheers people Much appreciated Dave
  8. Time to fork out on new tyres. Whats the largest tyres that can be fitted safely to uk spec 9.5 rears. The 255's werent doing the job so is 265 or 275 an option? cheers Dave
  9. Yeah yeah we know your always right but we just dont admit it for obvious reasons
  10. Yeah was thinking i was pushing it slightly. Was just going to leave it and hope for the best but il maybe see if i can get a 1.2rr. What can the uk turbos be run at out of interest?
  11. Yeah still stock Jspec turbos
  12. After all the hassle iv had it ended up being the Greddy FCD that was causing car to run lean. AVA adjusted it on the rollers and it now has a safe mix with no detination. That allowed boost to be raised upto 1.25-1.3 and achieved 349rwhp. I found that AVA dont have a specific knowledge of supras but their general knowledge was enough to find the issue and deal with it. Ill go back there from now on with any issues or just to see the car on rollers again;) Cheers Dave
  13. In the words of Nic "Waste of time on stock turbos". Thats the to the point response i wanted. Cheers people Dave
  14. Is there much benefit in fitting uk cams injectors to a jspec or is it a waste if time. Is it a simple swap Cheers Dave
  15. There is no boost controller but i have a boost gauge. With rr in gauge reads 1bar and without its approx 1.25(thats with 1st cat out and 2nd still in). On whether the car was lean before parts were fitted i dont know. Basically as soon as the fcd and pump were fitted i took out rr(1.25bar) and took car straight to get fueling checked. Was told it was badly lean on this setup but i hadnt had fueling checked on previous 1bar setup before fcd and pump were fitted so i dont know how it was before. I noticed when the stem seals were getting done that there was alot of oil in head so im starting to wonder if it has been running lean and caused damage to a piston. Ill need to get a leak down test done to confirm this. One other thing that has had me puzzled is wiring inside engine bay which is white and has "FET Tuning System" printed on it. All the connectors from this wiring are just lying loose doing nothing. Going to just bite the bullet and get the fuelling/boost etc checked on rollers at AVA and just hope they know what their doin Cheers Dave
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.