Ryan.G

http://a2.sphotos.ak.fbcdn.net/hphotos-ak-ash3/538749_10151152393624561_1869335160_n.jpg Backed up with 7.93 http://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/375939_10151152394089561_1789967409_n.jpg

Fastest supra in the world on pump fuel! Well done Mate! Just shows how good the knock control is on Syvecs to handle that power on pump!

Fuel pressure trip will cause it to hit an early rpm limiter. The only cut on the Ecu which will turn off the engine on your car and stop it starting again is Oil pressure trip! Where is the oil pressure sensor plumbed in? Logs will tell you all and there is a manual on how to pull logs etc on http://www.syvecs.co.uk

Pat @ Scoobyclinic Paul @ zenperformance Dave Rowe @ Eps Also Lyndon on here also but not sure he wants to get back into it In the road market these are the guys I would recommend if not around.

Seeing as over 30 Supras with autos and over 500ftlb with a Syvecs have been spot on for last 3 years I would like to see some evidence that it was related to over torque event. Is the box out yet and stripped? My thoughts are that the filter was blocked still.

Thanks Mate Its a rare colour with only about 5 in the UK but does go well. Just my clutch A has taken some serious abuse and slipping from over the 80 launchs i have had to do developing the syvecs kit. When they are changes soon i will get a run in. Reckon a 10.4 @130 ish

http://www.syvecs.com/forum/viewtopic.php?f=8&t=322

Was a typo but will 500 shot of nitrous it would do it !

http://www.syvecs.com/downloads/SyvecsSetup-Generic-2011-08-15.exe

The launch was setup for only a 4000rpm launch at moment which compared to how hard I had the cars in the US launching is very tame but a transmission is not cheap and Jurgen drives to the track and back so I will always go slow and analysis data before turning stuff up. This car will easily do a 1.4 60ft which will straight away put it down to an 9.3. Then we have more boost to play with Great day though

Gents, after reading the thread and how the owner has described it failed it does not sound like an over torque issue. Have done around 20 autos over 500ftlb on Syvecs which have been spot on. Sounds like line pressure has slowly dropped which could be a blocked filter, Faulty solenoid, faulty sensor or seal blown. Ryan

Will speak today or tomorrow Hodge before I go to US There is a manual here which explains how to pull logs and lots more!! http://www.syvecs.com/support.php

Mark Newmans just done a 10.7 @131 on a 66mm turbo with new Syvecs Launch Strategy

https://dl.dropbox.com/u/71964971/Dash2%20Install%20INFO.doc

I think we should take 2 push bikes and do a Charity comp for quickest 1/4 on a push bike

Paid for Drag Racing

I had a good excuse that I was just on the way back to bed after a heavy night out in Brighton! Was good to catch up with everyone

Dnk! Your a machine Mate!

Hi Mike Back in UK now On Some of the Installations with all the sensors fitted there just isn't enough inputs to get all 4 wheels speeds so you can use just one of the fronts for the reference speed and carefully configure the Lat G TC tables. If you are not getting a RR speed value then that will be the issue with the ABS light and it needs to be resolved for TC to work on the S6. Great you are getting involved though and hope the manual has helped. With regards the Fuel pressure error the sensor wiring needs to be check. Check there is a 5v feed to Sensor, Ground and then a 0-5v signal output. With engine running it will be around 2volts IIRC. The Signal from Fuel pressure goes to pin59 on the S6GP connector on your install. Not always the same for every install for anyone else reading this. I would not take it out without fixing these issues as the Relative trip will be present at limit DBW opening and Rev Limit. Ryan

Managed to break one at high rpm and need one to help a friend in Denmark. Anyone got one spare Please pm me

Looks so much better with those wheels Rich! Sorry couldn't make it ive had a crazy week with getting everything done before i go to Denmark tomorrow and then Greece week after. Will catch up when back

Lyndon! Make it so you can send the analog inputs over Can and we could sell you units as an I/0 expander aswell Keep up good work and really pleased you are feeling better. Ryan

Gearbox adaptor and flywheel sold So Turbo kit, Injectors, rad, intercooler are up for £2000.

Give me a call tomorrow mate on number above

Hi If you want the turbo kit and then 2soops wants the other bits im happy for this to work. Best if you called tomorrow to go over more as im on mibile internet at moment away Ryan - 07812786303